View IP100ALF_4129558.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IP100A LF
Preliminary Data Sheet
Integrated 10/100 Ethernet MAC + PHY
Features
Single chip 10/100BASE, half or full duplex Ethernet Media Access Controller IEEE 802.3 compliant 100BASE-TX/100BASE-FX/10BASE-T PCI Bus master scatter/gather DMA on any byte boundary Full operation with PCI Clock from 25 MHz to 33 MHz PCI Revision 2.2 compliant On-chip transmit and receive FIFO buffers On-chip LED drivers Power management capabilities for ACPI 1.0 compliant systems WakeOnLAN support Management statistics gathering IP multicast receive and filter support using 64 bit hash table Transmit polling Auto pad insertion for short packets Programmable minimum Inter Packet Gap Supports auto MDI-MDIX function Smart Cable Analyzer (SCA) Support Capable of using 93C46 EEPROM On-chip crystal oscillator On-chip voltage regulator 2.5/3.3V CMOS with 5V tolerant I/O 0.25m technology 128-pin PQFP Support Lead Free package (Please refer to the Order Information)
General Description
The IP100A LF is a single-chip, full duplex, 10/100Mbps Ethernet MAC + PHY incorporating a 32-bit PCI with bus master support. The IP100A LF is designed for use in a variety of applications including workstation NICs, PC motherboards, and other systems utilizing a PCI bus that require network connectivity to an Ethernet or Fast Ethernet LAN. The IP100A LF includes a PCI bus interface unit, IEEE 802.3 compliant MAC, transmit and receive FIFO buffers, IEEE 802.3 compliant 100BASE-TX, 10BASE-T, and 100BASE-FX PHY, serial EEPROM interface and LED drivers. The IP100A LF implements a rich set of control and status registers. Accessible via the PCI interface, these registers provide a host system visibility into the features and operating state of the IP100A LF. Network management statistics are also recorded, and host access to registers of the PHY device are facilitated through the IP100A LF's PCI interface. The IP100A LF supports features for use in "Green PCs" or systems where control over system power consumption is desired. The IP100A LF supports several power down states, and the ability to issue a system "wake event" via reception of unique, user defined Ethernet frames. In addition, the IP100A LF can assert a wake event in response to changes in the Ethernet link status
1/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
Block Diagram
PCI
RSTN PCICLK GNTN IDSEL INTAN PMEN REQN AD[31..0] CBEN[3:0] PAR FRAMEN IRDYN TRDYN DEVSELN STOPN PERRN SERRN VDET
MDI
TXP TXN RXP RXN TxDMA TxFIFO Logic Media PCI Bus Access Control Interface (MAC) RxDMA RxFIFO Logic (PCS, PMA, PMD) Physical Layer FFSD
EEPROM
EEOP EEDO EEDI EESK EECS
MISCELLANEOUS
X1 X2 ISET
LED
LED_LINK LED_10N LED_100N LED_TXN LED_RXN LEDDPLXN
LAST_GASP CTRL25 TEST
RSTN
VCC2 VCC1 AVCC25 AVCC33 GND
FIGURE 1: IP100A LF Block Diagram
2/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
Contents
Features....................................................................................................................................................... 1 General Description..................................................................................................................................... 1 Block Diagram ............................................................................................................................................. 2 Contents ...................................................................................................................................................... 3 Revision History........................................................................................................................................... 6 1 PIN Designations .................................................................................................................................. 7 2 PIN Diagram.......................................................................................................................................... 8 3 PIN Descriptions ................................................................................................................................... 9 PIN Descriptions (continued) ................................................................................................................... 10 PIN Descriptions (continued) ................................................................................................................... 11 4 Acronyms and Glossary...................................................................................................................... 13 5 Standards Compliance........................................................................................................................ 13 6 Functional Description ........................................................................................................................ 13 6.1 Media Access Control............................................................................................. 13 6.2 Physical Layer ........................................................................................................ 14 6.3 On-Chip Voltage Regulator..................................................................................... 14 6.4 PCI Bus Interface.................................................................................................... 14 6.5 TxDMA Logic .......................................................................................................... 14 6.6 TxFIFO.................................................................................................................... 15 6.7 RxDMA Logic .......................................................................................................... 15 6.8 RxFIFO ................................................................................................................... 15 6.9 EEPROM Interface ................................................................................................. 15 7 Operation ............................................................................................................................................ 16 7.1 Initialization ............................................................................................................. 16 7.2 Register Programming............................................................................................ 16 7.3 TxDMA and Frame Transmission........................................................................... 17 7.4 Frame Reception and RxDMA................................................................................ 19 7.5 Interrupts................................................................................................................. 22 8 Statistics.............................................................................................................................................. 22 8.1 Transmit Statistics .................................................................................................. 22 8.2 Receive Statistics ................................................................................................... 23 9 PCI Bus Master Operation .................................................................................................................. 23 10 Power Management............................................................................................................................ 24 10.1 Wake Event............................................................................................................. 27 10.2 Power Down ........................................................................................................... 27 11 Registers and Data Structures............................................................................................................ 28 11.1 PHY Registers ........................................................................................................ 28 11.1.1 Control Register...................................................................................................... 28 11.1.2 Status Register ....................................................................................................... 29 11.1.3 PHY Identifier 1....................................................................................................... 30 11.1.4 PHY Identifier 2....................................................................................................... 30 11.1.5 Auto-Negotiation Advertisement............................................................................. 31 11.1.6 Auto-Negotiation Link Partner Ability...................................................................... 31 11.1.7 Phy Specification Control Register ......................................................................... 32 11.1.8 Phy Debug Control Register ................................................................................... 33 11.1.9 Phy Status Monitor Register ................................................................................... 33 11.1.10 SCA Settings .......................................................................................................... 34 11.2 DMA Data Structures.............................................................................................. 35 11.2.1 RxDMAFragAddr .................................................................................................... 35 11.2.2 RxDMAFragLen ...................................................................................................... 36 11.2.3 RxDMANextPtr ....................................................................................................... 36 11.2.4 RxFrameStatus....................................................................................................... 36
3/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.2.5 11.2.6 11.2.7 11.2.8 11.3 11.3.1 11.3.2 11.3.3 11.3.4 11.3.5 11.4 11.4.1 11.4.2 11.4.3 11.4.4 11.4.5 11.4.6 11.4.7 11.4.8 11.4.9 11.4.10 11.4.11 11.4.12 11.4.13 11.4.14 11.4.15 11.4.16 11.4.17 11.4.18 11.4.19 11.4.20 11.4.21 11.4.22 11.4.23 11.4.24 11.4.25 11.4.26 11.4.27 11.5 11.5.1 11.5.2 11.5.3 11.5.4 11.5.5 11.5.6 11.5.7 11.5.8 11.5.9 11.5.10 11.5.11 11.5.12 11.5.13 11.5.14 11.5.15 11.5.16 TxDMAFragAddr..................................................................................................... 38 TxDMAFragLen ...................................................................................................... 38 TxDMANextPtr ........................................................................................................ 38 TxFrameControl...................................................................................................... 39 Wake Event Data Structures .................................................................................. 40 MagicSequence ...................................................................................................... 41 MagicSyncStream................................................................................................... 41 PseudoCRC ............................................................................................................ 41 PseudoPattern ........................................................................................................ 42 Terminator............................................................................................................... 42 LAN I/O Registers................................................................................................... 43 AsicCtrl.................................................................................................................... 44 DMACtrl .................................................................................................................. 48 EepromCtrl.............................................................................................................. 50 EepromData............................................................................................................ 51 FIFOCtrl .................................................................................................................. 51 HashTable............................................................................................................... 52 IntEnable................................................................................................................. 52 IntStatus.................................................................................................................. 53 IntStatusAck............................................................................................................ 54 MACCtrl0 ................................................................................................................ 55 MACCtrl1 ................................................................................................................ 56 MaxFrameSize........................................................................................................ 58 PhyCtrl .................................................................................................................... 58 ReceiveMode.......................................................................................................... 59 RxDMABurstThresh................................................................................................ 59 RxDMAListPtr ......................................................................................................... 60 RxDMAPollPeriod ................................................................................................... 60 RxDMAStatus ......................................................................................................... 60 RxDMAUrgentThresh ............................................................................................. 61 StationAddress ....................................................................................................... 62 TxDMABurstThresh ................................................................................................ 62 TxDMAListPtr.......................................................................................................... 63 TxDMAPollPeriod ................................................................................................... 63 TxDMAUrgentThresh.............................................................................................. 64 TxReleaseThresh ................................................................................................... 64 TxStatus.................................................................................................................. 65 WakeEvent.............................................................................................................. 66 Statistic Registers ................................................................................................... 67 BroadcastFramesReceivedOk................................................................................ 67 BroadcastFramesTransmittedOk............................................................................ 67 CarrierSenseErrors................................................................................................. 68 FramesAbortedDueToXSColls ............................................................................... 68 FramesLostRxErrors............................................................................................... 69 FramesReceivedOk ................................................................................................ 69 FramesTransmittedOk ............................................................................................ 70 FramesWithDeferredXmission................................................................................ 70 FramesWithExcessiveDeferal................................................................................. 71 LateCollisions ......................................................................................................... 71 MulticastFramesReceivedOk.................................................................................. 72 MulticastFramesTransmittedOk.............................................................................. 72 MultipleCollisionFrames.......................................................................................... 73 OctetsReceivedOk.................................................................................................. 73 OctetsTransmittedOk.............................................................................................. 74 SingleCollisionFrames ............................................................................................ 74
4/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
LAN PCI Configuration Registers ........................................................................... 75 CacheLineSize........................................................................................................ 76 CapId ...................................................................................................................... 76 CapPtr..................................................................................................................... 76 CISPointer............................................................................................................... 77 ClassCode .............................................................................................................. 77 ConfigCommand..................................................................................................... 78 ConfigStatus ........................................................................................................... 79 Data ........................................................................................................................ 80 DeviceId .................................................................................................................. 80 ExpRomBaseAddress............................................................................................. 81 HeaderType ............................................................................................................ 81 InterruptLine............................................................................................................ 82 InterruptPin ............................................................................................................. 82 IoBaseAddress ....................................................................................................... 82 LatencyTimer .......................................................................................................... 83 MaxLat .................................................................................................................... 83 MemBaseAddress .................................................................................................. 83 MinGnt .................................................................................................................... 84 NextItemPtr ............................................................................................................. 84 PowerMgmtCap ...................................................................................................... 85 PowerMgmtCtrl ....................................................................................................... 86 RevisionId ............................................................................................................... 86 SubsystemId ........................................................................................................... 87 SubsystemVendorId ............................................................................................... 87 VendorId ................................................................................................................. 87 11.7 EEPROM Data Format ........................................................................................... 88 11.7.1 AsicCtrl.................................................................................................................... 88 11.7.2 ConfigParm ............................................................................................................. 89 11.7.3 FunctionsCtrl........................................................................................................... 90 11.7.4 StationAddress ....................................................................................................... 90 11.7.5 SubsystemId ........................................................................................................... 91 11.7.6 SubsystemVendorId ............................................................................................... 91 12 Signal Requirements........................................................................................................................... 92 12.1 Absolute Maximum Ratings .................................................................................... 92 12.2 Operating Ranges................................................................................................... 92 12.3 AC Characteristics .................................................................................................. 94 12.4 Thermal Data .......................................................................................................... 96 13 Order Information ................................................................................................................................ 96 14 Physical Dimensions ........................................................................................................................... 97 11.6.1 11.6.2 11.6.3 11.6.4 11.6.5 11.6.6 11.6.7 11.6.8 11.6.9 11.6.10 11.6.11 11.6.12 11.6.13 11.6.14 11.6.15 11.6.16 11.6.17 11.6.18 11.6.19 11.6.20 11.6.21 11.6.22 11.6.23 11.6.24 11.6.25 11.6
5/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
Revision History
Revision Number Version 1.0 Version 10 Version 11 Version 12 Version 13 Version 14 Version 15 Version 16 Version 17 Date 2003-06-25 2005-01-25 2005-03-14 2005-04-22 2005-05-19 2005-10-20 2006-04-27 2006-10-18 2007-03-30 First Release 1. Add the order information for lead free package. 1. Modify pin name of Pin 17,18,20,21,22,24,35,43,48,49 1. Describe EepromCtrl register bit 12 and bit 13 in detail 1. Add IP100A thermal data 1. Remove 93C56 and EEOP support. 2. Modify FFSD pin definition, in page 11. 1. Add "Support Auto MDI-MDIX function" description 1. Modify RxDMALastFrag pin description, in page 36. 1. Modify Pin Diagram in page 8. 2. Modify LED_LINK Pin Type in page 11 Revision
6/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
1 PIN Designations
PIN NAME PIN NO. NC 33 AD5 34 AD4 35 AD3 36 NC 37 AD2 38 AD1 39 NC 40 AD0 41 NC 42 VCC2 43 NC 44 GND 45 LED_LINK 46 NC 47 LED_TXN 48 EESK / 49 LED_10N EEDI / 50 LED_100N GND 51 NC 52 LED_RXN 53 EEDO 54 /LED_DPLXN GND 55 VCC1 56 TEST 57 NC 58 NC 59 EECS 60 NC 61 LAST_GASPN 62 X2 63 X1 64 PIN NAME GND ISET AVSS TXP TXN NC AVCC25 NC RXP RXN AVSS AVCC25 CTRL25 AVSS AVCC33 NC NC NC NC NC NC NC NC NC NC NC INTAN VDET RSTN GNTN PMEN NC PIN NO. 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 PIN NAME GND VCC2 PCICLK REQN AD31 AD30 AD29 AD28 AD27 VCC2 GND AD26 AD25 GND AD24 CBEN3 VCC1 IDSEL AD23 AD22 AD21 AD20 GND AD19 GND AD18 VCC2 VCC1 AD17 NC AD16 CBEN2 PIN NO. 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 PIN NAME GND NC VCC2 FRAMEN IRDYN TRDYN DEVSELN STOPN PERRN VCC1 SERRN PAR GND GND VCC2 CBEN1 AD15 AD14 AD13 AD12 AD11 AD10 NC VCC1 VCC2 GND AD9 AD8 CBEN0 AD7 AD6 FFSD
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
TABLE 1 : IP100A LF Pin Designations
7/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
2 PIN Diagram
TRDYN IRDYN FRAMEN VCC2 NC GND CBE2N AD16 NC AD17 VCC1 VCC2 AD18 GND AD19 GND AD20 AD21 AD22 AD23 IDSEL VCC1 CBE3N AD24 GND AD25 AD26 GND VCC2 AD27 AD28 AD29 AD30 AD31 REQN PCICLK VCC2 GND 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
DEVSELN STOPN PERRN VCC1 SERRN PAR GND GND VCC2 CBE1N AD15 AD14 AD13 AD12 AD11 AD10 NC VCC1 VCC2 GND AD9 AD8 CBE0N AD7 AD6 FFSD
103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
IP100A LF
IC Plus Corp. Fast Ethernet NIC Chip
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39
NC PMEN GNTN RSTN VDET INTAN NC NC NC NC NC NC NC NC NC NC NC AVCC33 AVSS CTRL25 AVCC25 AVSS RXN RXP NC AVCC25
Copyright (c) 2004, IC Plus Corp.
NC AD5 AD4 AD3 NC AD2 AD1 NC AD0 NC VCC2 NC GND LED_LINK NC LED_TXN EESK / LED_10N EEDI / LED_100N GND NC LED_RXN EEDO / LED_DPLXN GND VCC1 TEST NC NC EECS NC LAST_GASPN X2 X1 GND ISET AVSS TXP TXN NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
8/97
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
3 PIN Descriptions
PIN NAME PIN TYPE PIN DESCRIPTION Reset, asserted LOW. RSTN will cause the IP100A LF to reset all of its functional blocks. RSTN must be asserted for a minimum duration of 10 PCICLK cycles. PCI Bus Clock. This clock is used to drive the PCI bus interfaces and the internal DMA logic. All bus signals are sampled on the rising edges of PCICLK. PCICLK can operate from 25MHz to 33MHz. PCI Bus Grant, asserted LOW. GNTN signals access to the PCI bus has been granted to IP100A LF. Initialization Device Select. The IDSEL is used to select the IP100A LF during configuration read and write transactions. Interrupt Request, asserted LOW. The IP100A LF asserts INTAN to request an interrupt, when any one of the programmed interrupt event occurs. Wake Event, assertion level is programmable (see the WakePolarity bit of the WakeEvent register). The IP100A LF asserts PMEN to signal the detection of a wake event. Request, asserted LOW. The IP100A LF asserts REQN to request PCI bus master operation. PCI Bus Address/Data. Address and data are multiplexed on the AD pins. The AD pins carry the physical address during the first clock cycle of a transaction, and carry data during the subsequent clock cycles. PCI Bus Command/Byte Enable, asserted LOW. Bus command and byte enables are multiplexed on the CBEN pins. CBEN specify the bus command during the address phase transaction, and carry byte enables during the data phase. Parity. PCI Bus parity is even across AD[31..0] and CBEN[3..0]. The IP100A LF generates PAR during address and write data phases as a bus master, and during read data phase as a target. It checks for correct PAR during read data phase as bus master, during every address phase as a bus slave, and during write data phases as a target. PCI Bus Cycle Frame, asserted LOW. FRAMEN is an indication of a transaction. It is asserted at the beginning of the address phase of the bus transaction and de-asserted before the final transfer of the data phase of the transaction. Initiator Ready, asserted LOW. A bus master asserts IRDYN to indicate valid data phases on AD[31..0] during write data phases, indicates it is ready to accept data during read data phases. A target will monitor IRDYN. Target Ready, asserted LOW. A bus target asserts TRDYN to indicate valid read data phases, and to indicate it is ready to accept data during write data phases. A bus master will monitor TRDYN. Stop, asserted LOW. STOPN is driven by the slave target to inform the bus master to terminate the current transaction. TABLE 2 : IP100A LF Pin Descriptions
PCI INTERFACE RSTN INPUT
PCICLK
INPUT
GNTN IDSEL INTAN
INPUT INPUT OUTPUT
PMEN
OUTPUT
REQN AD [31..0] CBEN [3..0]
OUTPUT IN/OUT
IN/OUT
PAR
IN/OUT
FRAMEN
IN/OUT
IRDYN
IN/OUT
TRDYN
IN/OUT
STOPN
IN/OUT
9/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
PIN Descriptions (continued)
PIN NAME PIN TYPE PCI INTERFACE (continued) PERRN IN/OUT PIN DESCRIPTION
Parity Error, asserted LOW. The IP100A LF asserts PERRN when it checks and detects a bus parity errors. When it is generating PAR output, the IP100A LF monitors for any reported parity error on PERRN. System Error, asserted LOW. Power Detect. The IP100A LF detects PCI bus power supply loss when VDET is LOW. EEPROM Chip Select. EECS is asserted by the IP100A LF to access the EEPROM. EECS is connected directly to the chip select input of the EEPROM device. EEPROM Serial Clock. EESK is an output connected directly to the clock input of the EEPROM device. EEPROM Data Input. EEDI is an output connected directly to the data input of the EEPROM device. This pin is shared with LED100N pin. EEPROM Data Output. EEDO is an input connected directly to the data output of the EEPROM device. This pin is shared with Duplex LED pin. Transmit Status LED. This pin will stay LOW during transmission period and HIGH if no data or pulse is beening sent from IP100A LF. Receiving Status LED. This pin will stay LOW during receiving period and if no data has been received, the LED_RXN status will be HIGH. Duplex Status LED. LED_DPLXN is the duplex status LED driver. The duplex status LED driver is LOW when the link is full duplex, and HIGH when the link is half duplex. Additional functionality of the speed status LED signal is based on the LEDMode bit of the AsicCtrl register. TABLE 2 : IP100A LF Pin Descriptions
SERRN VDET
OUTPUT INPUT
EEPROM INTERFACE EECS OUTPUT
EESK EEDI EEDO
OUTPUT OUTPUT INPUT
LED DRIVERS LED_TXN OUTPUT LED_RXN OUTPUT
LED_DPLXN OUTPUT
10/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
PIN Descriptions (continued)
PIN NAME PIN TYPE PIN DESCRIPTION LED DRIVERS (continued) LED_10N OUTPUT 10Mb/sec Connection Status LED. This pin will output LOW to indicate 10Mb/sec Transmission if the connection between 2 devices have negoatiated to link at 10Mb/sec. LED_100N OUTPUT 100Mb/sec Connection Status LED. This pin will output LOW to indicate 100Mb/sec Transmission if the connection between 2 devices have negoatiated to link at 100Mb/sec. LED_LINK OUTPUT Link Status LED. LED_LINK is the link status LED driver. The functionality of the link status LED signal is based on the LEDMode bit of the AsicCtrl register. A 4.7K pull-down resistor is placed between this pin and GND regardless of whether the LED is connected to this pin. MDI RXP INPUT Receive input. When in 100BASE-TX mode, this receives MLT3 data from the isolation transformer. When in 100BASE-FX mode, this is a PECL input. RXN INPUT Receive input. When in 100BASE-TX mode, this receives MLT3 data from the isolation transformer. When in 100BASE-FX mode, this is a PECL input. TXP OUTPUT Transmit output. When in 100BASE-TX mode, this is an MLT-3 driver. When in 100BASE-FX mode, this is a PECL driver. TXN OUTPUT Transmit output. When in 100BASE-TX mode, this is an MLT-3 driver. When in 100BASE-FX mode, this is a PECL driver. FFSD INPUT This pin is used to select TP or Fiber mode. For 100BASE-FX applications, FFSD is connected to the signal detect output pin of a fiber optic module at PECL level. Connecting this pin to GND will force the IP100A into TP mode. MISCELLANEOUS CTRL25 OUTPUT This is a controller pin to monitor correct 2.5V supply to IC. LAST_GASPN INPUT This pin monitors the PCI voltage. If the voltage is dropped to certain value, LAST_GASPN will indicate IP100A LF to transmit LAST GASP frame to inform the other end that IP100A LF is not functioning till SYSTEM POWER ON or RESET. X1 OSCIN 25MHz Crystal Oscillator Input. The external 25MHz crystal and capacitor is connected to the on-chip crystal oscillator circuit through X1 input. Alternately, X1 can be driven by an external clock source. X2 OSCOUT 25MHz Crystal Oscillator Output. The external crystal and capacitor is also connected to the output of the on-chip crystal oscillator circuit through X2. When X1 is driven by an external clock source, X2 should be left unconnected. ISET ANALOG Band Gap Resistor. Connect a 6.2kohm, 1% resister between ISET and GND. TEST INPUT Test. Enables the IP100A LF test modes. NC Reserved. These Pins must keep floating at application circuit. POWER AND GROUND VCC2 POWER +3.3 volt I/O power supply. VCC1 POWER +2.5 volt digital logic power supply. AVCC25 POWER +2.5 volt analog power supply. AVCC33 POWER +3.3 volt analog power supply. AVSS GROUND Analog Ground
11/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
PIN NAME GND PIN TYPE GROUND Power return. PIN DESCRIPTION
TABLE 2 : IP100A LF Pin Descriptions
12/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
4 Acronyms and Glossary
Local Area Network Media Access Control Layer, or a device implementing the functions of this layer (a Media Access Controller) PCI Peripheral Component Interface NIC Network Interface Cards FIFO First In First Out EPROM Erasable Programmable Read Only Memory EEPROM Electrically Erasable Programmable Read Only Memory LED Light Emitting Diode PHY Physical Layer, or device implementing functions of the Physical Layer CSMA/CD Carrier Sense Multiple Access with Collision Detect FCS Frame Check Sequence SFD Start of Frame Delimiter CRC Cyclic Redundancy Check IP Internet Protocol TFD Transmit Frame Descriptor RFD Receive Frame Descriptor DMA Direct Memory Access ACPI Advanced Configuration and Power Management LAN MAC
5
Standards Compliance
The IP100A LF implements functionality compliant with the following standards: * IEEE 802.3 Fast Ethernet * IEEE 802.3 Full Duplex Flow Control * PCI Local Bus Revision 2.2 * PCI Bus Power Management Interface Revision 1.1 * ACPI Revision 1.0
6
Functional Description
The IP100A LF is composed of various functional blocks as shown in Figure 1 on page 2. An overview of the functions performed by each block are as follows: 6.1 Media Access Control
The MAC block implements the IEEE Ethernet 802.3 Media Access Control functions with 802.3 Full Duplex and Flow Control enhancements. In half duplex mode, the MAC implements the CSMA/CD algorithm. Full duplex mode by definition does not utilize CSMA/CD, allowing data to be transmitted on demand. An optional flow control mechanism in full duplex mode is provided via the MAC Control PAUSE function. Additionally, the MAC also performs the following functions in either half or full duplex mode: * Optional transmit FCS generation * Padding to the minimum legal frame size * Preamble and SFD generation * Preamble and SFD removal * Receive frame FCS checking and optional FCS stripping * Receive frame destination address matching * Support for multicast and broadcast frame reception or rejection (via filtering) * Selective InterFrame Gap to avoid capture effect * MAC Loopback The MAC is responsible for generation of hardware signals to update the internal statistics counters.
13/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
6.2 Physical Layer
The IP100A LF supports both IEEE 802.3 100BASE-TX and 100BASE-FX signaling. The 100BASE-X transmit logic performs 4B5B encoding/decoding, parallel to serial, and serial to parallel conversion, and NRZ-NRZI signaling. In the case of 100BASE-TX, scrambling and MLT-3 encoding are also done before the data is transmitted on to the media. The receive 100BASE-X circuitry, recovering data from either an MLT-3 signal (100BASE-TX) or a PECL input (100BASE-FX), generates four bit nibbles to send to the MAC. The Media Dependent Interface selection is done by the FFSD pin. If the FFSD pin is connected directly to GND, the IP100A LF PHY layer is operating in TX mode. If FFSD is connected to the signal detect, then the PHY layer is in 100BASE-FX mode. The IP100A LF PHY also includes a full set of registers for controlling the PHY as outlined in the IEEE 802.3 specification. 6.3 On-Chip Voltage Regulator
The IP100A LF has an integrated voltage regulator for reduced system cost. The voltage regulator is used to provide the 2.5 V power to the PCB. When used with a 2N2905 PNP transistor based circuit as shown in Figure 2, the CTRL25 pin will regulate the current through the transistor, providing a stable 2.5 V reference.
VCC2 VCC1
IP100A LF CTRL25 150
MMBT2907A
Voltage Comparator inside IC 2.2K, 1%
33 0.1u
2.0K, 1%
FIGURE 2: External PNP Transistor Based Regulator Circuit 6.4 PCI Bus Interface
The PCI Bus Interface implements the protocols and signals needed to operate the IP100A LF in a PCI bus. The IP100A LF can be either a PCI bus master or slave. The PCI Bus Interface is also responsible for managing the DMA interfaces and the host processors access to the IP100A LF registers. Arbitration logic within the PCI Bus Interface block accepts bus requests from the TxDMA Logic and RxDMA Logic. The PBI also manages interrupt generation for a host processor. 6.5 TxDMA Logic
The IP100A LF supports a multi-frame, multi-fragment DMA gather process. Descriptors representing frames are built and linked in system memory by a host processor. The TxDMA Logic is responsible for transferring the multi-fragment frame data from the host memory into the TxFIFO. The TxDMA Logic monitors the amount of free space in the TxFIFO, and uses this value to decide when to request a TxDMA. A TxDMABurstThresh register is used to delay the bus request until there is enough free space in the TxFIFO for a long burst.
14/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
To prevent a TxFIFO under run condition the TxDMA logic forwards an urgent request to the arbiter, regardless of the TxDMABurstThresh constraint, when the number of occupied bytes in the TxFIFO drops below the value in TxDMAUrgentThresh register. 6.6 TxFIFO
The IP100A LF uses 2K bytes of transmit data buffer between the TxDMA Logic and Transmit MAC. When the TxDMA logic determines there is enough space available in the TxFIFO, the TxDMA Logic will move any pending frame data into the TxFIFO. The TxReleaseThresh register value determines the amount of data which must be transmitted out of the TxFIFO before the FIFO memory space occupied by that data can be released for use by another frame. A TxReleaseError occurs when a frame experiences a collision after the TxFIFO release threshold has been crossed. The IP100A LF will not be able to retransmit this frame from the TxFIFO and the complete frame must be transferred from the host system memory to the TxFIFO again by TxDMA Logic. 6.7 RxDMA Logic
The IP100A LF supports a multi-frame, multi-fragment DMA scatter process. Descriptors representing frames are built and linked in system memory by the host processor. The RxDMA Logic is responsible for transferring the frame data from the RxFIFO to the host memory. The RxDMA Logic monitors the number of bytes in the RxFIFO. After a number of bytes have been received, the frame is "visible". A frame is visible if: * The frame being received is determined not to be a runt, OR * The entire frame has been received After a frame becomes visible, the RxDMA Logic will issue a request to the arbiter when the number of bytes in the RxFIFO is greater than the value in the RxDMABurstThresh. To prevent receive overruns, a RxDMA Urgent Request is made when the amount of free space in the RxFIFO falls below the value in RxDMAUrgentThresh. 6.8 RxFIFO
The IP100A LF uses 2K bytes of receive data buffer between the Receive MAC and RxDMA Logic. The values in RxDMABurstThresh determine how many bytes of a frame must be received into RxFIFO before RxDMA Logic is allowed to begin data transfer. 6.9 EEPROM Interface
The external serial EEPROM is used for non-volatile storage of such information as the node address, system ID, and default configuration settings. As part of initialization after system reset, the IP100A LF reads from the EEPROM and places the data into certain host-accessible registers. IP100A LF is able to read and write to 93LC46 series EEPROM. The correct connection is shown in section 17.2.
15/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
7
7.1
Operation
Initialization
The IP100A LF provides several resets. The assertion of the hardware reset signal on the PCI bus causes a complete reset of the IP100A LF. A similar reset is available via software using the GlobalReset bit of the AsicCtrl register. The AsicCtrl register also allows for selective reset of particular functional blocks of the IP100A LF. See the Registers and Data Structures section for details on using the AsicCtrl register for resetting the IP100A LF. Shortly after reset, the IP100A LF will read the contents of an external EEPROM, placing the data read into the following registers: * ConfigParm * AsicCtrl (least significant 16 bits) * SubsystemVendorId * SubsystemId * StationAddress * Data There are several other registers which must be configured by the host during initialization. These registers include the IP100A LF PCI configuration registers which are set during a Power On Self Test (POST) routine performed by the host system. Specifically, the registers set during this stage of initialization are: * ConfigCommand enables adapter operation by allowing it to respond to and generate PCI bus cycles. ConfigCommand is also used to enable parity error generation. * loBaseAddress sets the I/O base address for the IP100A LF registers. * MemBaseAddress sets the memory base address for the IP100A LF registers. * ExpRomBaseAddress sets the base address and size for an installed expansion ROM, if any. * CacheLineSize indicates the system's cache line size. This value is used by the IP100A LF to optimize bus master data transfers. * LatencyTimer sets the length of time the IP100A LF can hold the PCI bus as a bus master. * InterruptLine maps IP100A LF's interrupt request to a specific interrupt line (level) on the system board. * AsicCtrl is used to setup internal operations and parameters. The IP100A LF can be accessed across the PCI bus without setting the PCI registers or loading data from an external EEPROM. In this Forced Configuration mode (useful for embedded applications without an EEPROM), the IP100A LF is configured as follows: * I/O base address 0x200 * I/O target cycles enabled * Memory target cycles disabled * Bus master cycles enabled 7.2 Register Programming
After initialization, an additional set of registers specific to operation of the Ethernet network must be programmed. The first setting relates to the Auto-Negotiation function. The IP100A LF PHY layer performs the Auto-Negotiation process, and the host system must communicate with the PHY to determine the link status. Once the result of Auto-Negotiation is determined, if a full duplex mode has been chosen, the host system must set the FullDuplexEnable bit in the MACCtrl0 register. Other modes chosen during Auto-Negotiation do not require any IP100A LF register settings. The ReceiveMode register determines which types of frames, based on address matching mechanism, the IP100A LF will receive. The end station address is loaded from the EEPROM, or the host system can
16/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
set the address directly. Then, by setting the ReceiveUnicast bit in the ReceiveMode register, the IP100A LF will receive unicast frames whose destination address matches the value in the StationAddress register. The ReceiveMulticastHash bit in ReceiveMode enables a filtering mechanism for Ethernet multicast frames. This filtering mechanism uses a 64-bit hash table (HashTable register) for selective reception of Ethernet multicast frames. Additionally, Ethernet frames containing IP multicast destination addresses can also be received by setting the ReceiveIPMulticast bit in the ReceiveMode register. IP multicast, or Host Extension for IP Multicasting, datagrams map to frames with Ethernet destination addresses of 0x01005e****** (where * represents any hexadecimal value). The MACCtrl0 and MACCtrl1 registers are used to configure parameters including full duplex, flow control, and statistics gathering. In half duplex mode, the IP100A LF implements the CSMA/CD algorithm. If multiple nodes on the same network attempt to transmit simultaneously, a collision will occur resulting in re-transmission. In full duplex mode, the IP100A LF can transmit and receive frames simultaneously without incurring collisions. To configure the IP100A LF for full duplex mode operation, the host system must detect a full duplex physical link via the PHY Status Register, and must set the FullDuplexEnable bit in the MACCtrl0 register. The IEEE 802.3x Full Duplex standard defines a special frame known as the PAUSE MAC Control frame. The PAUSE frame is used to implement flow control in full duplex networks allowing stations on opposite ends of a full duplex link the ability to inhibit transmission of data frames for a specified period of time. The PAUSE frame format is defined as shown in Figure 3.
FIELD DA 0x0180C2000001 LENGTH (BYTES) 6
SA
6
TYPE OPCODE PAUSE TIME PAD
0x8808 0x0001
2 2 2 42
FIGURE 3: PAUSE Frame Whenever the FlowControlEnable bit in the MACCtrl0 register is set, the IP100A LF looks for any incoming PAUSE frame. If found, the IP100A LF inhibits transmission of all data frames for the time specified in the two-byte pause_time field. The pause_time field is specified in slot times relative to the current data rate; one slot time is 51.2 us at 10 Mbps, and 5.12 us at 100 Mbps. The transmission of PAUSE frames is the responsibility of the host. The MAC Control frame must be constructed by the host and placed into the TxFIFO. For end station applications, host system should only accept PAUSE frames, and not generate them. Flow control is designed to originate from network devices such as switches. 7.3 TxDMA and Frame Transmission
The TxDMA Logic transfers frame data from the host system memory to the IP100A LF based on a
17/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
linked list of frame descriptors called TFDs. The host system creates a list of TFDs in system memory, where each TFD contains the memory locations of one or more fragments of a frame as shown in Figure 4.
HOST SYSTEM MEMORY
TxDMANextPtr TxFrameControl 1st TxDMAFragAddr 1st TxDMAFragLen TFD 2nd TxDMAFragAddr 2nd TxDMAFragLen
Last TxDMAFragAddr Last TxDMAFragLen
1st Data Frag (Buffer)
2nd Data Frag (Buffer)
Last Data Frag (Buffer)
FIGURE 4: TxDMA Data Structure The TFD format is covered in the Registers and Data Structures section. The resulting linked list of TFDs is referred to as the TxDMAList, as shown in Figure 5.
HOST SYSTEM MEMORY TFD1
TFD2
FIGURE 5: TxDMA List of Two TFDs
18/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
In the simple case of a single frame, the host system must create a TFD within the host system memory containing the addresses and lengths of the fragments of data to be transmitted. The host system must write zero into TxDMANextPtr since this is the only frame. The host starts the TxDMA Logic by writing the memory location (a non-zero address) of the TFD into TxDMAListPtr register. The TxDMA Logic begins transferring data into the IP100A LF. The IP100A LF first fetches the fragment addresses and fragment lengths from the TFD and writes them one at a time into registers, which are used to control the data transfer operations. If the TxDMA Logic transfers more data than can fit into the TxFIFO, an overrun will occur. The TxDMAListPtr I/O register within the IP100A LF contains the physical address that points to the head of the TxDMAList. TxDMAListPtr must point to addresses which are on 8-byte boundaries. A value of zero in the TxDMAListPtr register implies there are no pending TFD's for the IP100A LF to process. Generally, it is desirable for the host system to queue multiple frames. Multiple TFD's are linked together in a list by pointing the TxDMANextPtr of each TFD at the next TFD. The last TFD in the linked list should have a value of zero for it's TxDMANextPtr. The TxDMA process returns to the idle state upon detection of a zero value for TxDMANextPtr. When a new frame is available to transfer, the host system must write the address of the new TFD into the TxDMANextPtr memory location of the last TFD, and either set the TxEnable bit, or utilize the IP100A LF's automatic polling capability. Using automatic polling, the IP100A LF will monitor the TxDMANextPtr memory location until a non-zero value is found at that location in system memory. The TxDMAPollPeriod register controls this polling function, which is enabled when TxDMAPollPeriod contains a non-zero value. The value written to TxDMAPollPeriod determines the TxDMANextPtr polling interval. In response to a TxDMAComplete interrupt, when data transfer by TxDMA is finished, the host acknowledges the interrupt and returns the frame data buffers to the system. In the case of a multi-frame TxDMAList, multiple frames may have been transferred by TxDMA when the host system enters its interrupt service routine. The host system can traverse the list of TFD's, examining the TxDMAComplete bit in each TFD to determine which frames have been transferred by TxDMA. The IP100A LF fetches the TFC before frame data transfer, and again at the end of TxDMA operation to examine the TxDMAIndicate bit. This allows the host system to change TxDMAIndicate while data transfer of the frame is in progress. For instance, a frame's TFD might be at the end of the TxDMAList when it starts TxDMA, so the host system would probably set TxDMAIndicate to generate an interrupt. However, if during the TxDMA process of this frame, the host system added a new TFD to the end of the list, it might clear TxDMAIndicate in the currently active TFD so that the interrupt is delayed until the next TFD. The IP100A LF has the ability to automatically round up the length of a transmit frame. This is useful in some NOS environments in which frame lengths need to be an even number of words. The frame length is rounded up to either a word or dword boundary, depending upon the value of WordAlign. Host systems may disable frame length word-alignment by setting the WordAlign bits in the TransmitFrameControl to x1. The MAC will initiate frame transmission (if transmission is enabled) as soon as either the entire frame is resident in the TxFIFO register. As a frame transmits out of the TxFIFO, it is desirable to be able to release the FIFO space so that it may be used for another frame. The value programmed into TxReleaseThresh determines how much of a frame must be transmitted before its FIFO space can be released. 7.4 Frame Reception and RxDMA
The frame RxDMA mechanism is similar to the TxDMA mechanism. RxDMA is structured around a
19/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
linked list of frame descriptors, called RFDs. RFDs contain pointers to the fragment buffers into which the IP100A LF is to place receive data, as shown in Figure 6.
HOST SYSTEM MEMORY
RxDMANextPtr RxFrameStatus 1st RxDMAFragAddr 1st RxDMAFragLen RFD 2nd RxDMAFragAddr 2nd RxDMAFragLen
Last RxDMAFragAddr Last RxDMAFragLen
1st Data Frag (Buffer)
2nd Data Frag (Buffer)
Last Data Frag (Buffer)
FIGURE 6: RxDMA Data Structure The RFD format is covered in the Registers and Data Structures section. Similar to TFDs, the resulting linked list of RFDs is referred to as the RxDMAList. One option available to RxDMA that differs from TxDMA is that the RxDMAList can be formed into a ring as shown in Figure 7. A host system can allocate a number of full size frame buffers, create a RFD for each one, and link the RFDs into a circular list. As frames are received and transferred by RxDMA, a RxDMAComplete interrupt will be generated for each frame.
20/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
HOST SYSTEM MEMORY RFD 1
RFD 2
RFD n
FIGURE 7: RxDMA List Shown in Ring The host system must create a RxDMAList and the associated buffers prior to reception of a frame. One approach calls for the host system to allocate a block of full size (i.e. large enough to hold a maximum size Ethernet frame of 1518 bytes) frame buffers in system data space and create RFDs that point to them. Another approach is for the host system to request the buffers from the protocol ahead of time. After reset, the IP100A LF receive function is disabled. Once the RxEnable bit is set, frames will be received according to the matching mode programmed in ReceiveMode register. Reception can be disabled by setting the RxDisable bit. If set while a frame is being received, RxDisable only takes effect after the active frame reception is finished.The receive function begins with the RxDMA Logic in the idle state. The RxDMA Logic will begin processing a RxDMAList as soon as a non-zero address is written into the RxDMAListPtr register. The host system creates a RFD with the addresses and lengths of the buffers to be used and programs the RxDMAListPtr register to point to the head of the list. The host system must program a zero into the RxDMANextPtr of the last RFD to indicate the end of the RxDMAList. When a frame is received in the RxFIFO, the IP100A LF fetches the fragment address and fragment length values one by one from the current RFD, and writes these values into internal registers which controliA 9 oR -! bjbjyIyI yy Y l P y Y yy yy yy l P P P P
o , , , A I of the RFD from which the host system has finished The IP100A LF RxDMAPollPeriod is zero the host system should also issuewhen RxDMA completes a reading data. If can be configured to generate a RxDMAComplete interrupt a RxDMAResume in case frame transfer. In response a RxDMAComplete interrupt, the host system must examine the the IP100A LF has halted due to detection of a set RxDMAComplete bit within the ReceiveFrameStatus ReceiveFrameStatus in the ring. If the IP100A LF frame a RxDMAListPtr for a RFD that has already field of the next RFDfield in the RFD of the receivedfetchesto determine the size of the frame and whether there used (a RFD in The host RxDMAComplete bit is set in ReceiveFrameStatus), the RxDMA Logic been were any errors. which the system must then copy the frame out of the receive buffers, if needed. will either assert an implicit RxDMAHalt or, if the RxDMAPollPeriod register is set to a non-zero value, In general, when the automatically enters its interrupt service periodically until itframes may have been the RxDMA Logic will host system recheck RxDMAComplete routine, multiple is cleared. transferred by RxDMA. The host system can read RxDMAListPtr to determine which RFDs in the list have been used. The host system begins at the head of the RFD list, and traverses the list until it reaches the RFD whose address matches RxDMAListPtr. However, since I/O operations are costly, it is more efficient to use the RxDMAComplete bit in each RFD to determine which frames have been transferred by RxDMA.
21/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
T
IP100A LF
Preliminary Data Sheet
In some host systems, it may be desirable to copy received frame data out of the scatter buffer to the protocol buffer while the frame is still being transferred by RxDMA. The RxDMAStatus register is provided for this purpose. If the host system sets the RxDMAHalt bit in the DMACtrl register, reads the RxDMAListPtr register and the RxDMAStatus register, then sets the RxDMAResume bit in the DMACtrl register, the host system can determine how much of the frame has been transferred by RxDMA. The RxDMAStatus register indicates the number of bytes transferred by RxDMA for the current RFD pointed to by the RxDMAListPtr register. The host system can then perform memory copies out of the RFD buffer concurrently with the RxDMA operation. 7.5 Interrupts
The term "interrupt" is used loosely to refer to interrupts and indications. An interrupt is the actual assertion of the hardware interrupt signal on the PCI bus. An indication, or a set bit in the IntStatus register, is the reporting of any event enabled by the host. The host system will configure the IP100A LF to generate an interrupt for any indication that is of interest to it. There are 10 different types of interrupt indications that can be generated by the IP100A LF. The IntEnable register controls which of the 10 indication bits can assert a hardware interrupt. In order for an indication bit to be allowed to generate an interrupt, its corresponding bit-position in IntEnable must be set. When responding to an interrupt, the host reads the IntStatus register to determine the cause of the interrupt. The least significant bit of IntStatus, InterruptStatus, is always set whenever any of the interrupts are asserted. InterruptStatus must be explicitly acknowledged (cleared) by writing a 1 into the bit in order to prevent spurious interrupts on the host bus. Interrupts are acknowledged by the host carrying out various actions specific to each interrupt.
8
Statistics
The IP100A LF implements 16 statistics counters of various widths. Each statistic implemented complies to the corresponding definition given in the IEEE 802.3 standard. Setting the StatisticsEnable bit in the MACCtrl1 register enables the gathering of statistics. Reading a statistics register will clear the read register. Statistic registers may be read without disabling statistics gathering. For diagnostics and testing purposes, the host system may write a value to a statistic register, in which case the value written is added to the current value of the register. Whenever one or more of the statistics registers reaches 75% of its maximum value, an UpdateStats interrupt is generated. Reading that statistics register will acknowledge the UpdateStats interrupt. A summary of the transmit and receive statistics follows. Detailed descriptions of the statistic registers related to data transmission and reception can be found in the Registers and Data Structures section. 8.1 Transmit Statistics
* FramesTransmittedOk: The number frames of all types transmitted without errors. Loss of carrier is not considered to be an error by this statistic. * BroadcastFramesTransmittedOk: The number of frames with broadcast destination address that are transmitted without errors. * MulticastFramesTransmittedOk: The number of frames with multicast destination address that are transmitted without errors. * OctetsTransmittedOk: The number of total octets for all frames transmitted without error. * FramesWithDeferredXmission: A count of frames whose transmission was delayed on it's first attempt because network traffic. * FramesWithExcessiveDeferral: If the transmission of a frame has been deferred for an excessive period of time due to network traffic, the event is recorded in this statistic. * SingleCollisionFrames: Frames that are transmitted without errors after one and only one collision (including late collisions) are counted by this register. * MultipleCollisionFrames: All frames transmitted without error after experiencing from 2 through 15 collisions (including late collisions) are counted here.
22/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
* LateCollisions: Every occurrence of a late collision (there could be more than one per frame transmitted) is counted by this statistic. * FramesAbortedDueToXSColls: If the transmission of a frame had to be aborted due to excessive collisions, the event is recorded in this statistic. * CarrierSenseErrors: Frames that were transmitted without error but experienced a loss of carrier are counted by this statistic. 8.2 Receive Statistics
* FramesReceivedOk: Frames of all types that are received without error are counted here. * BroadcastFramesReceivedOk: Frames of broadcast destination address that are received without error are counted here. * MulticastFramesReceivedOk: Frames of multicast destination address that are received without error are counted here. * OctetsReceivedOk: A total octet count for all frames received without error. * FramesLostRxErrors: This is a count of frames that would otherwise be received by the IP100A LF, but could not be accepted due to an overrun condition in the RxFifo.
9
PCI Bus Master Operation
The IP100A LF supports all of the PCI memory commands and decides on a burst-by-burst basis which command to use in order to maximize bus efficiency. The list of PCI memory commands is shown below. For all commands, "read" and "write" are with respect to the IP100A LF (i.e. read implies the IP100A LF obtains information from an off-chip location, write implies the IP100A LF sends information to an off-chip location). * Memory Read (MR) * Memory Read Multiple (MRM). * Memory Write (MW) * Memory Write Invalidate (MWI) MR is used for all fetches of descriptor information. For reads of transmit frame data, MR, or MRM is used, depending upon the remaining number of bytes in the fragment, the amount of free space in the TxFIFO, and whether the RxDMA Logic is requesting a bus master operation. MW is used for all descriptor writes. Writes of receive frame data use either MW or MWI, depending upon the remaining number of bytes in the fragment, the amount of frame data in the RxFIFO, and whether the TxDMA Logic is requesting a bus master operation. The IP100A LF provides three configuration bits to control the use of advanced memory commands. The MWlEnable bit in the ConfigCommand configuration register allows the host to enable or disable the use of MWI. The MWIDisable bit in DMACtrl allows the host system the ability to disable the use of MWI. MWIDisable is cleared by default, enabling MWI. The IP100A LF provides a set of registers that control the PCI burst behavior. These registers allow a trade-off to be made between PCI bus efficiency and under run/overrun frequency. Arbitration logic within the PCI Bus Interface block accepts bus requests from the TxDMA Logic and RxDMA Logic. The TxDMA Logic uses the TxDMABurstThresh register, as described in the TxDMA Logic section, to delay the bus request until there is enough free space in the TxFIFO for a long, efficient burst. The TxDMA Logic can also make an urgent bus request as described in the TxDMA Logic section, where burst efficiency is sacrificed in favor of avoiding a TxFIFO under run condition. The RxDMA process is described in the RxDMA Logic section. Typically, RxDMA requests will be forwarded to the Arbiter, however RxDMA Urgent Requests are also possible in order to prevent RxFIFO overruns.
23/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
10 Power Management
The IP100A LF supports operating system directed power management according to the ACPI specification. Power management registers in the PCI configuration space, as defined by the PCI Bus Power Management Interface specification, Revision 1.0 are described in 10.0. The IP100A LF supports several power management states. The PowerState field in the PowerMgmtCtrl register determines IP100A LF's current power state. The power states are defined as follows: * D0 Uninitialized (power state 0) is entered as a result of hardware reset, or after a transition from D3 Hot to D0. This state is the same as D0 Active except that the PCI configuration registers are uninitialized. In this state, the IP100A LF is unable to respond to PCI I/O, memory and configuration cycles and can not operate as a PCI master The IP100A LF cannot signal wake (PMEN) from the D0 state. * D0 Active (power state 0) is the normal operational power state for the IP100A LF. In this state, the PCI configuration registers have been initialized by the system, including the IoSpace, MemorySpace, and Bus-Master bits in ConfigCommand, so the IP100A LF is able to respond to PCI I/O, memory and configuration cycles and can operate as a PCI master. The IP100A LF cannot signal wake (PMEN) from the D0 state. * D1 (power state 1) is a "light-sleep" state. The IP100A LF optionally supports this state determined by the D1Support bit in the ConfigParm word in EEPROM. The D1 state allows transition back to D0 with no delay. In this state, the IP100A LF responds to PCI configuration accesses, to allow the system to change the power state. In D1 the IP100A LF does not respond to any PCI I/O or memory accesses. The IP100A LF's function in the D1 state is to recognize wake events and link state events and pass them on to the system by asserting the PMEN signal on the PCI bus. * D2 (power state 2) is a partial power-down state. The IP100A LF optionally supports this state determined by the D2Support bit in the ConfigParm word in EEPROM. D2 allows a faster transition back to D0 than is possible from the D3 state. In this state, the IP100A LF responds to PCI configuration accesses, to allow the system to change the power state. In D2 the IP100A LF does not respond to any PCI I/O or memory accesses. The IP100A LF's function in the D2 state is to recognize wake events and link state events and pass them on to the system by asserting the PMEN signal on the PCI bus. * D3 Hot (power state 3) is the full power-down state for the IP100A LF. In D3 Hot, the IP100A LF loses all PCI configuration information except for the value in PowerState. In this state, the IP100A LF responds to PCI configuration accesses, to allow the system to change the power state back to D0 Uninitialized. In D3 hot, the IP100A LF does not respond to any PCI I/O or memory accesses. The IP100A LF's main responsibility in the D3 Hot state is to recognize wake events and link state events and signal those to the system by asserting the PMEN signal on the PCI bus. * D3 Cold (power state undefined) is the power-off state for the IP100A LF. The IP100A LF does not function in this state. When power is restored, the system guarantees the assertion of hardware reset, which puts the IP100A LF into the D0 Uninitialized state. The IP100A LF can generate wake events to the system as a result of Wake Packet reception, Magic Packet reception, or due to a change in the link status. The WakeEvent register gives the host system control over which of these events are passed to the system. Wake events are signaled over the PCI bus using the PMEN pin. A Wake Packet event is controlled by the WakePktEnable bit in WakeEvent register. WakePktEnable has no effect when IP100A LF is in the D0 power state, as the wake process can only take place in states D1, D2, or D3. When the IP100A LF detects a Wake Packet, it signals a wake event on PMEN (if PMEN assertion is enabled), and sets the WakePktEvent bit in the WakeEvent register. The IP100A LF can signal that a wake event has occurred when it receives a pre-defined frame from another station. The host system transfers a set of frame data patterns into the transmit FIFO using the transmit DMA function before placing the IP100A LF in a power-down state. Once powered down, the IP100A LF compares receive frames with the frame patterns in the transmit FIFO. When a matching frame is received (and also passes the filtering mode set in the ReceiveMode register), a wake event is signaled.
24/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
The frame patterns in the transmit FIFO specify which bytes in received frames are to be examined. Each byte in the transmit FIFO specifies a four bit relative offset (from the start of the received frame) in the most significant nibble and a four bit length indicator in the least significant nibble. Relative offsets describe the number of bytes of the received frame to skip from the last relevant byte, beginning with byte 0x00. Relative offsets with a value of 0xF indicate the actual relative offset is larger than 15, and is specified by the next 8 bit value in the transmit FIFO. Length indicators with a value of 0xF indicate the actual length indicator is larger than 15, and is specified by the next 8 bit value in the transmit FIFO. If both the relative offset, and the length indicator are 0xF, the first byte following the relative offset/length indicator pair is the actual relative offset, and the second following byte is the actual length indicator. A byte value of 0x00 indicates the end of the pattern for that wake frame. Immediately following the end-of-pattern is a 4-byte CRC. The calculation used to for the CRC is the same polynomial as the Ethernet MAC FCS. An example pseudo-packet (based on the ARP packet example from Appendix A of the "OnNow Network Device Class Power Management Specification") which would be loaded into the transmit FIFO of the IP100A LF is shown in Figure 8.
TxFIFO 0xc2 0x71 0xf4 0x10 pseudo packet 0x00 0xf3 0x19 0x08 0xd7
FIGURE 8: Example Pseudo Packet Using the pseudo packet in Figure 8, the IP100A LF will assert a wake event if a packet of the form shown in Figure 9 is received whereby a 32-bit CRC over the indicated bytes of the received packet yields the value 0xf31908d7.
25/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
Received Packet byte 12 byte 13 byte 21 byte 38 byte 39 byte 40 byte 41 Byte Offset Within Packet 0x0c 0x0d 0x15 0x26 0x27 0x28 0x29
FIGURE 9: Example Wake Packet The IP100A LF also supports Magic PacketTM technology developed by Advanced Micro Devices to allow remote wake-up of a sleeping station on a network via transmission of a special frame. Once the IP100A LF has been placed in Magic Packet mode and put to sleep, it scans all incoming frames addressed to it for a data sequence consisting of 16 consecutive repetitions of its own 48-bit Ethernet MAC StationAddress. This sequence can be located anywhere within the frame, but must be preceded by a synchronization stream. The synchronization stream is defined as 6 bytes of 0xFF. For example, if the MAC address programmed into the StationAddress register is 0x11:22:33:44:55:66, then the IP100A LF would be scanning for the frame data shown in Figure 10.
Received Packet 0xFFFFFFFFFFFF 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566 0x112233445566
FIGURE 10: Example Magic Packet Magic Packet wake up is controlled by the MagicPktEnable bit in the WakeEvent register. A wake event
26/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
can only take place in the D1, D2, or D3 states, and MagicPktEnable has no effect when the IP100A LF is in the D0 power state. The Magic Packet must also pass the address matching criteria set in ReceiveMode. A Magic Packet may also be a broadcast frame. When the IP100A LF detects a Magic Packet, it signals a wake event on PMEN (if PMEN assertion is enabled), and sets the MagicPktEvent bit in WakeEvent. The IP100A LF can also signal a wake event when it senses a change in the network link state, either from LINK_OK to LINK_FAIL, or vice versa. Link state wake is controlled by the LinkEventEnable bit in the WakeEvent register. At the time LinkEventEnable is set by the host system, the IP100A LF samples the current link state. It then waits for the link state to change. If the link state changes before the IP100A LF returns to state D0 or LinkEventEnable is cleared, LinkEvent is set in WakeEvent, and (if it is enabled) the PMEN signal is asserted. 10.1 Wake Event
When a desired wake event occurs, the IP100A LF sets the appropriate event bit in the WakeEvent register, sets the PmeStatus bit in the PowerMgmtCtrl register, and asserts the PMEN signal. The host system responds to PMEN by scanning the power management configuration registers of all devices, looking for the device which asserted PMEN. If the device with the IP100A LF signaled wake, the system will find PmeStatus set in IP100A LF's PowerMgmtCtrl register. The operating system then clears the PmeEn bit in the PowerMgmtCtrl register causing PMEN to be de-asserted. The operating system raises the power state (probably to D0) by writing to the PowerState bits in the PowerMgmtCtrl register. If the IP100A LF was previously in the D3 state, PCI configuration is lost and must be restored by the operating system. The host system must set TxReset to clear any wake patterns out of the transmit FIFO (if this is not done, the patterns will be treated as frames and transmitted once the transmitter is enabled). The host system reads the WakeEvent register to determine the wake event, and if requested, passes it back to the operating system. The host system restores any volatile state that was saved in the power down sequence. The host system re-enables interrupts by programming IntEnable. The host system restores the RxDMAList (and any other data structures required for operation). Any wake packets in the receive FIFO are transferred by receive DMA and passed to the operating system. 10.2 Power Down
D0u and D0i are mutually exclusive. The moment that the IoBaseAddress register or the MemBaseAddress is written by the host, then IP100A LF enters D0u. When D0u is active, the PHY is completely powered down and all clocks (AsicClk, TxClk, RxClk) are gated off except PciClk. The IP100A LF consumes less than 70 mA in D0u. Make sure that the LED drivers are off. When IP100A LF is in D0i, the PHY is powered up and ready to transmit and receive packets. In Forced Config mode (motherboard applications), IP100A LF is always in D0i mode. Another way to indicate D0u is to check the non-zero value in the programmable field of IoBaseAddress or MemBaseAddress. In WOL the PHY should be fully functional to receive Magic Packets. In WOL mode, D0u should be forced to low before passing to the PHY. When in the D3 state, if PMEN is de-asserted on the PCI bus the IP100A LF will enter Power Down. When in Power Down mode, the PHY is completely powered down. All clocks (AsicClk, TxClk, RxClk) except PciClk are gated off. When the PCI bus is powered down, the IP100A LF consumes less than 5 mA.
27/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11 Registers and Data Structures
11.1 PHY Registers The IP100A LF includes a full set of PHY registers which can be accessed through the internal MDC/MDIO interface. The MAC and PHY, although integrated, act as if they are separate. The PHY registers must be accessed throught the PhyCtrl register. 11.1.1 Control Register Class............................. PHY Registers, Control Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x00 Default .......................... 0x3100 Width ............................ 16 bits BIT 15 BIT NAME Reset R/W R/W BIT DESCRIPTION 1 = Software Reset (self clearing). While the IP100A LF is resetting, Reset will remain a logic 1 and write attempts to any PHY Registers are not accepted. 0 = Normal operation. 1 = PHY loopback mode. When Loopback is a logic 1, the IP100A LF will be isolated from the network media. All transmit data from the MAC will return to the MAC as receive data. Collision indications are disabled unless Collision Test is a logic 1. 0 = Normal operation. 1 = 100 Mb/s. 0 = 10 Mb/s. 1 = Auto-negotiation enabled. 0 = Auto-negotiation disabled. 1 = PHY power down. When Power Down is a logic 1, the IP100A LF PHY will enter Power Down mode. While in Power Down mode, the IP100A LF PHY will not respond to transmit data, or received data but will respond to management transactions. 0 = Normal operation. 1 = Isolate PHY. When Isolate is a logic 1, the IP100A LF PHY will be isolated from the MAC. When isolated, the IP100A LF will not respond to transmit or receive data, but will respond to management transactions. 0 = Normal operation. 1 = Restart auto-negotiation (self clearing). When Restart Auto-Negotiation is a logic 1, the IP100A LF will restart Auto-Negotiation, depending on the Auto-Negotiation bit. If the Auto-Negotiation bit is a logic 0, then Restart Auto-Negotiation has no effect. 0 = Normal operation. 1 = Full duplex. 0 = Half duplex.
14
Loopback
R/W
13 12 11
Speed Auto-Negotiation Power Down
R/W R/W R/W
10
Isolate
R/W
9
Restart Auto-Negotiation
R/W
8
Duplex Mode
R/W
28/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 7 BIT NAME Collision Test R/W R/W BIT DESCRIPTION 1 = Enable COL test. If Collision Test is a logic 1 and transmit data is sent to the PHY, the IP100A LF PHY will assert the collision signal within 512 bit times (where 1 bit time = 100ns for 10Mbps operation and 1 bit time = 10ns for 100Mbps operation). When transmit data is removed, the IP100A LF PHY will deassert the collision signal within 4 bit times. 0 = Normal operation. Reserved for future use.
6..0
Reserved
N/A
11.1.2 Status Register Class............................. PHY Registers Access Method............. Accessed through PhyCtrl register Register Address.......... 0x01 Default .......................... 0x7849 Width ............................ 16 bits BIT 15 14 13 12 11 10..7 6 5 BIT NAME 100BASE-T4 100BASE-X Full Duplex 100BASE-X Half Duplex 10BASE-T Full Duplex 10BASE-T Half Duplex Reserved Preamble Suppression Auto-Negotiation Complete R/W R R R R R N/A R R BIT DESCRIPTION 1 = PHY 100BASE-T4 capable. 0 = PHY not 100BASE-T4 capable. 1 = PHY 100BASE-X Half Duplex capable. 0 = PHY not 100BASE-X Half Duplex capable. 1 = PHY 100BASE-X Half Duplex capable. 0 = PHY not 100BASE-X Half Duplex capable. 1 = PHY 10BASE-T Full Duplex capable. 0 = PHY not 10BASE-T Full Duplex capable. 1 = PHY 10BASE-T Half Duplex capable. 0 = PHY not 10BASE-T Half Duplex capable. Reserved for future use. 1 = Management preamble may be suppressed. 0 = Management preamble required. 1 = Auto-Negotiation complete. 0 = Auto-Negotiation not complete. If Auto-Negotiation Complete is a logic 1, the auto-negotiation process is complete and the contents of the Auto-Negotiation Link Partner Ability and Auto-Negotiation Expansion registers are valid. If Auto-Negotiation Complete is a logic 0, the Auto-Negotiation process is not complete, and the contents of the Auto-Negotiation Link Partner Ability and Auto-Negotiation Expansion registers are undefined. If the Auto-Negotiation bit of the Control Register is a logic 0, then Auto-Negotiation Complete is always a logic 0. 1 = Remote Fault detected. 0 = Remote Fault not detected. If Remote Fault is a logic 1, the IP100A LF has detected a remote fault condition. Remote Fault will remain a logic 1 until the remote fault condition no longer exists, and Remote Fault is read by the host system.
29/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
4
Remote Fault
R
IP100A LF
Preliminary Data Sheet
BIT 3 BIT NAME Auto-Negotiation Ability R/W R BIT DESCRIPTION 1 = Auto-Negotiation capable. 0 = Auto-Negotiation incapable. If Auto-Negotiation Ability is a logic 1, the IP100A LF is capable of performing Auto-Negotiation. Auto-Negotiation Ability depends on the external mode setting of the IP100A LF. 1 = Link is up. 0 = Link is down. When Link Status is a logic 0, Link Status will remain a logic 0 until the link state changes, and Link Status is read by the host system. 1 = Jabber detected. 0 = Jabber not detected. When Jabber Detect is a logic 1, Jabber Detect will remain a logic 0 until the jabber condition no longer exists, and Jabber Detect is read by the host system. 1 = Extended capabilities register exists.
2
Link Status
R
1
Jabber Detect
R
0
Extended Capability R
11.1.3 PHY Identifier 1 Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x02 Default .......................... 0x0243 Width ............................ 16 bits BIT 15..0 BIT NAME PHY ID Number R/W R BIT DESCRIPTION Bits 3 through 18 of the OUI. OUI = 0090C3
11.1.4 PHY Identifier 2 Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x03 Default .......................... 0x0D80 Width ............................ 16 bits BIT 15..10 9..4 3..0 BIT NAME PHY ID Number Model Number Revision Number R/W R R R BIT DESCRIPTION Bits 19 through 24 of the OUI. Manufacturer's model number. Four bit manufacturer's revision number.
30/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.1.5 Auto-Negotiation Advertisement Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x04 Default .......................... 0x01E1 Width ............................ 16 bits BIT 15 14 13 12..11 10 9 8 7 6 5 4..0 BIT NAME Next Page capable Reserved Remote Fault Reserved Pause 100BASE-T4 100BASE-TX Full Duplex 100BASE-TX Half Duplex 10BASE-T Full Duplex 10BASE-T Half Duplex Selector Field R/W R/W N/A R/W N/A R/W R/W R/W R/W R/W R/W R/W BIT DESCRIPTION 1 = Next Page capable. 0 = Next Page incapable. Reserved for future use. 1 = Remote Fault supported. 0 = Remote Fault not supported. Reserved for future use. 1 = Pause function supported. 0 = Pause not supported. 1 = 100BASE-T4 capable. 0 = 100BASE-T4 incapable. 1 = PHY 100BASE-TX Full Duplex capable. 0 = PHY not 100BASE-TX Full Duplex capable. 1 = PHY 100BASE-TX Half Duplex capable. 0 = PHY not 100BASE-TX Half Duplex capable. 1 = PHY 10BASE-T Full Duplex capable. 0 = PHY not 10BASE-T Full Duplex capable. 1 = PHY 10BASE-T Half Duplex capable. 0 = PHY not 10BASE-T Half Duplex capable. IEEE 802.3 selector field
11.1.6 Auto-Negotiation Link Partner Ability Class............................. PHY Registers Access Method............. Accessed through PhyCtrl register Register Address.......... 0x05 Default .......................... 0x0000 Width ............................ 16 bits BIT 15 14 13 BIT NAME Next Page Acknowledge Remote Fault R/W R R R BIT DESCRIPTION 1 = Next Page capable. 0 = Next Page incapable. 1 = Link Code Word received. 0 = Link Code Word not received. 1 = Remote Fault detected. 0 = Remote Fault not detected. If Remote Fault is a logic 1, then the Remote Fault bit of the Status Register register will be a logic 1. Reserved for future use. 1 = 100BASE-T4 capable. 0 = 100BASE-T4 incapable.
31/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
12..10 9
Reserved 100BASE-T4
N/A R
IP100A LF
Preliminary Data Sheet
BIT 8 7 6 5 4..0 BIT NAME 100BASE-TX Full Duplex 100BASE-TX Half Duplex 10BASE-T Full Duplex 10BASE-T Half Duplex Selector Field R/W R R R R R BIT DESCRIPTION 1 = 100BASE-TX Full Duplex capable. 0 = Not 100BASE-TX Full Duplex capable. 1 = 100BASE-TX Half Duplex capable. 0 = Not 100BASE-TX Half Duplex capable. 1 = 10BASE-T Full Duplex capable. 0 = Not 10BASE-T Full Duplex capable. 1 = 10BASE-T Half Duplex capable. 0 = Not 10BASE-T Half Duplex capable. Selector Field
11.1.7 Phy Specification Control Register Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x16 Default .......................... 0x03A4 Width ............................ 16 bits BIT 15:6 5 4 BIT NAME Reserved AUTOMDIX_ON FEF_DISABLE R/W RO R/W BIT DESCRIPTION AutoCrossOver can be set to enabled by setting this bit to 1, even when AN is disabled Set high to disable the functionality of Far-End Fault when the chip operates at fiber mode 0: Enable FEF 1: Disable FEF Set high to let IP100A LF operate at repeat mode 0: Not Repeat mode 1: Repeat mode Set high to enable jabber detection mechanism when IP100A LF operates at 10BASE-T 0: Disable 1: Enable Set high to enable heartbeat detection mechanism when IP100A LF operates at 10BASE-T 0: Disable 1: Enable Set high to disable DSP reset watch-dog timer 0: Not Bypass 1: Bypass
3
REPEAT_MODE
R/W
2
JABBER_ENA
R/W
1
HEARTBEAT_ENA
R/W
0
BYPASS_DSPRST
R/W
32/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.1.8 Phy Debug Control Register Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x17 Default .......................... 0x0000 Width ............................ 16 bits BIT 15:6 5 4 3 2 1..0 BIT NAME Reserved DSP_SPEED_UP FORCE_LINK BYPASS_SCRAM R/W RO RW RW RW BIT DESCRIPTION Reserved for future use Set high to speed up all timers during NWAY procedure Set high to speed up DSP training sequcences Set high to force link-up Set high to bypass PCS scrambler/de-scrambler These 2 bits are used to select NWAY debug output
NWAY_SPEED_UP RW
NWAY_DEBUG_SE RW L
11.1.9 Phy Status Monitor Register Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x18 Default .......................... 0x0000 Width ............................ 16 bits BIT 15 14 13 12 11 BIT NAME LDSP_SLEEPING LINK_OK DESCRAM _LOCK 10BASE_ POLARITY RESLOVED _SPEED RESLOVED _DUPLEX MDI/MDIX R/W RO RO RO RO RO BIT DESCRIPTION When set to high, indicating IP100A LF is in link-down sleeping mode When set to high, indicating link status is OK When set to high, indicating PCS de-scrambler is locked on data When set to high, indicating the cable polarity is reversal (this bit is meaningful only chip operates at 10BASE-T) To indicate the resolved speed mode 0: 10BASE-T 1: 100BASE-TX/FX To indicate the resolved duplex mode 0: Half Duplex 1: Full Duplex To indicate either at MDI or MDIX state 0: MDI (Not Crossover) 1: MDIX(Crossover) NWAY debug output
10
RO
9
RO
8..0
NWAY_DEBUG _OUT
RO
33/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.1.10 SCA Settings Class............................. PHY Registers Access Method ............. Accessed through PhyCtrl register Register Address .......... 0x22 Default .......................... 0x0000 Width ............................ 16 bits BIT 15 14 13..11 10 9..8 BIT NAME SCA_mode SCA_chsel Reseverd SCA_tx_pulse SCA_phase R/W R/W R/W N/A R/W R/W 1=set to SCA mode. 0=default. 1= Test MDIX channel. 0= Test MDI channel Reseve for future use 1= Send a pulse for each write operation 0= do nothing 00= phase do not increment 01= phase increment by 1 for each write operation 11= phase decrement by 1 for each write operation 10= Reserved ADC outputs capture time after sending a pulse. The value must be greater than 0 for a capture event BIT DESCRIPTION
7..0
SCA_capture_len
R/W
34/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.2 DMA Data Structures A TFD is used to move data destined for transmission onto an Ethernet network, from the host system memory to the transmit FIFO within the IP100A LF. A TFD is 16 to 512 bytes in length, and it's location in host system memory is indicated by the value in the TxDMAListPtr register. A RFD is used to move data obtained from an Ethernet network, from the receive FIFO within the IP100A LF to the host system memory. A RFD is 16 to 512 bytes in length, and it's location in host system memory is indicated by the value in the RxDMAListPtr register. There are two formats for an RFD, differentiated by the ImpliedBufferEnable bit of the RxFrameStatus field. Figure 11 shows the two DMA data structures.
HOST SYSTEM MEMORY
Offset from TFD Start TxDMANextPtr TxFrameControl TxDMAFragAddr0 TxDMAFragLen0 TFD TxDMAFragAddr1 TxDMAFragLen1 0x00 0x04 0x08 0x0c 0x10 0x14 RFD RxDMANextPtr RxFrameStatus RxDMAFragAddr0 RxDMAFragLen0 RxDMAFragAddr1 RxDMAFragLen1
HOST SYSTEM MEMORY
Offset from RFD Start 0x00 0x04 0x08 0x0c 0x10 0x14
TxDMAFragAddrn TxDMAFragLenn
0x08+n*0x08 0x0C+n*0x08
RxDMAFragAddrn RxDMAFragLenn
0x08+n*0x08 0x0C+n*0x08
FIGURE 11: TFD and RFD DMA Data Structures 11.2.1 RxDMAFragAddr Class............................. DMA Data Structures, RFD Base Address ............... Start of RFD Address Offset .............. 0x08+n*0x08 for nth fragment (where n=0,1,...63) Access Mode ................ Read/Write Width ............................ 32 bits BIT 31..0 BIT NAME RxDMAFragAddr BIT DESCRIPTION Receive DMA Fragment Address. The RxDMAFragAddr contains the physical address of a contiguous block of system memory to which receive data is to be transferred by receive DMA. A fragment can start on any byte boundary.
35/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.2.2 RxDMAFragLen Class............................. DMA Data Structures, RFD Base Address ............... Start of RFD Address Offset .............. 0x0C+n*0x08 for nth fragment (where n=0,1,...63) Access Mode ................ Read/Write Width ............................ 32 bits The RxDMAFragLen contains fragment length and control information for the block of data pointed to by the corresponding RxDMAFragAddr. BIT 12..0 30..13 31 BIT NAME FragLen Reserved RxDMALastFrag BIT DESCRIPTION Fragment Length. The length of the contiguous block of data pointed to by the previous RxDMAFragAddr. Reserved for future use. Set by the host system to indicate the last fragment of the receive frame.
11.2.3 RxDMANextPtr Class............................. DMA Data Structures, RFD Base Address ............... Start of RFD Address Offset .............. 0x00 Access Mode ................ Read/Write Width ............................ 32 bits BIT 31..0 BIT NAME RxDMANextPtr BIT DESCRIPTION Receive DMA Next Pointer. RxDMANextPtr contains the physical address of the next RFD in the receive DMA list. For the last RFD in the receive DMA list, RxDMANextPtr must be 0x00000000. RFDs must be aligned on 8-byte physical address boundaries.
11.2.4 RxFrameStatus Class............................. DMA Data Structures, RFD Base Address ............... Start of RFD Address Offset .............. 0x04 Access Mode ................ Read/Write Width ............................ 32 bits At the end of a receive DMA transfer, the IP100A LF writes the value of the RxDMAStatus register to RxFrameStatus. BIT 12..0 BIT NAME RxDMAFrameLen BIT DESCRIPTION Receive DMA Frame Length. RxDMAFrameLen indicates the true frame length, except in the case where the frame is larger than the total number of bytes specified in all of the FragLen subfields of the RxDMAFragLen RFD field in which case, the RxDMAOverflow bit will be set. Reserved for future use.
13
Reserved
36/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 14 BIT NAME RxFrameError BIT DESCRIPTION Receive Frame Error. RxFrameError indicates that an error occurred during receipt of the frame. The host system should examine RxFIFOOverrun, RxRuntFrame, RxAlignmentError, RxFCSError, and RxOversizedFrame to determine the type of error(s). RxFrameError is undefined until RxDMAComplete is a logic 1. Receive DMA Complete. RxDMAComplete indicates the frame transfer from the IP100A LF to the host system is complete. Receive FIFO Overrun. RxFIFOOverrun indicates the data was not removed from the receive FIFO fast enough to keep up with the rate data was entering the receive FIFO from the media. Bytes may be missing from the frame at one or more unpredictable locations within the frame. RxFIFOOverrun is undefined until RxDMAComplete is a logic 1. Received Runt Frame. RxRuntFrame indicates the received frame was a runt (less than 60 bytes in length, measured from the DA field to the end of the Data field). RxRuntFrame is undefined until RxDMAComplete is a logic 1. Receive Alignment Error. RxRuntFrame indicates that the received frame had an alignment error. RxAlignmentError is undefined until RxDMAComplete is a logic 1. Receive Frame Check Sequence Error. RxFCSError indicates a FCS checksum error on the frame data. RxFCSError is undefined until RxDMAComplete is a logic 1 Receive Oversized Frame. RxOversizedFrame indicates the frame size was equal to or greater than the value set in the MaxFrameSize register. RxOversizedFrame is undefined until RxDMAComplete is a logic 1. Reserved for future use. Dribble Bits. DribbleBits indicates that the frame had accompanying dribble bits. DribbleBits is informational only, and does not indicate a frame error. Receive DMA Overflow. RxDMAOverflow indicates that the RFD did not have sufficient buffer space to hold all of the frame data. For this condition, the IP100A LF transfers as much data as possible and discards the remainder of the frame. Reserved for future use.
15 16
RxDMAComplete RxFIFOOverrun
17
RxRuntFrame
18
RxAlignmentError
19
RxFCSError
20
RxOversizedFrame
22..21 23
Reserved DribbleBits
24
RxDMAOverflow
27..25 28
Reserved
31..29
ImpliedBufferEnable Implied Buffer Enable. ImpliedBufferEnable enables a special receive DMA mode. If ImpliedBufferEnable is a logic 1 when the IP100A LF reads the RFD, the IP100A LF will assume there is one receive buffer of length 1528 bytes, starting immediately after ReceiveFrameStatus at (RFD address + 0x08). The host system sets ImpliedBufferEnable when it prepares the RFD. The IP100A LF tests ImpliedBufferEnable before receive DMA for a frame begins at the same time it tests the RxDMAComplete bit. When the IP100A LF updates RxFrameStatus field at the end of the receive DMA operation (in order to set RxDMAComplete) the value written to ImpliedBufferEnable is undefined. The host system cannot assume a certain value is left in ImpliedBufferEnable after the RFD is used. Therefore, the host system must write the desired value to ImpliedBufferEnable every time after releasing a RFD to the IP100A LF. Reserved Reserved for future use.
37/97 March. 30, 2007 IP100A LF-DS-R17
Copyright (c) 2004, IC Plus Corp.
IP100A LF
Preliminary Data Sheet
11.2.5 TxDMAFragAddr Class............................. DMA Data Structures, TFD Base Address ............... Start of TFD Address Offset.............. 0x08+n*0x08 for nth fragment (where n=0,1,...63) Access Mode................ Read/Write Width ............................ 32 bits BIT 31..0 BIT NAME TxDMAFragAddr BIT DESCRIPTION Transmit Fragment Address. TxDMAFragAddr contains the physical address of a contiguous block of data to be transferred from the host system to the IP100A LF. A fragment can start on any byte boundary.
11.2.6 TxDMAFragLen Class............................. DMA Data Structures, TFD Base Address ............... Start of TFD Address Offset .............. 0x0C+n*0x08 for nth fragment (where n=0,1,...63) Access Mode ................ Read/Write Width ............................ 32 bits Transmit Fragment Length (TxDMAFragLen) contains fragment length and control information for the block of data pointed to by the corresponding TxDMAFragAddr. BIT 12..0 BIT NAME FragLen BIT DESCRIPTION Fragment Length. FragLen is the length of the contiguous block of data pointed to by TxDMAFragAddr. The maximum fragment length is 8192 bytes. Reserved for future use. Transmit DMA Last Fragment. TxDMAFragLast is set by the host system to indicate the last fragment of the transmit frame and that the IP100A LF should proceed to the next TFD.
30..13 31
Reserved TxDMAFragLast
11.2.7 TxDMANextPtr Class............................. DMA Data Structures, TFD Base Address ............... Start of TFD Address Offset .............. 0x00 Access Mode ................ Read/Write Width ............................ 32 bits BIT 31..0 BIT NAME TxDMANextPtr BIT DESCRIPTION Transmit DMA Next Pointer. TxDMANextPtr contains the physical address of the next TFD in the transmit DMA list. A value of zero for TxDMANextPtr accompanies the last frame of the list and it indicates there are no more TFD's in the transmit DMA list. All TFD's must be aligned on a 8-byte physical address boundary.
38/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.2.8 TxFrameControl Class............................. DMA Data Structures, TFD Base Address ............... Start of TFD Address Offset .............. 0x04 Access Mode ................ Read/Write Width ............................ 32 bits TxFrameControl contains frame control information for the transmit DMA function and the transmit function. BIT 1..0 BIT NAME WordAlign BIT DESCRIPTION Word Alignment. WordAlign determine the boundary to which transmit frame lengths are rounded up in the transmit FIFO, and transmitted onto the network medium. BIT 1 BIT 0 ALIGNMENT 0 0 Align to Double Word 1 0 Align t o Word x 1 Alignment Disabled When using word alignment, it is the responsibility of the host system to recognize that any added bytes necessary to achieve the desired alignment may affect byte oriented functions and fields (i.e. if the Ethernet Length/Type field holds a frame length, this value is not updated to reflect any bytes added via word alignment). Frame Identification. FrameId can be used as a frame ID or sequence number and can be used by the host system (via the TxStatus register) to determine frames which experienced errors. Reserved for future use. FCS Append Disable. If FcsAppendDisable is a logic 1, the IP100A LF will not append the 4-byte FCS to the end of each transmit frame. In this case, the host system must supply the frame's FCS as part of the data transferred via transmit DMA. An exception exists when a transmit under run occurs; in this case a guaranteed-bad FCS will be appended to the frame by the IP100A LF. When FcsAppendDisable is a logic 0, the IP100A LF will compute and append FCS for each transmit frame. Reserved for future use. Transmit Indicate. If TxIndicate is a logic 1, the IP100A LF will issue a TxComplete interrupt when transmission of the frame completes. Transmit DMA Complete. When TxDMAComplete is a logic 1, the frame transfer by transmit DMA is complete. The IP100A LF sets TxDMAComplete to a logic 1 after completing transfer via transmit DMA, all fragments specified in the TFD. Reserved for future use. Transmit DMA Indicate. If TxDMAIndicate is a logic 1, the IP100A LF will issue a TxDMAComplete interrupt upon completion of transmit DMA for this frame. The TFC is read twice by the IP100A LF; the first time to write the TFC to the transmit FIFO before frame data transfer, and again after the transmit DMA operation is complete to test TxDMAIndicate in order to determine whether to generate an interrupt. This dual read process allows the host system time to change TxDMAIndicate while the transmit DMA transfer is in progress.
9..2
FrameId
12..10 13
Reserved FcsAppendDisable
14 15 16
Reserved TxIndicate TxDMAComplete
30..17 31
Reserved TxDMAIndicate
39/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.3 Wake Event Data Structures The first Wake Event Data Structure is the Pseudo Packet. A Pseudo Packet is a set of patterns loaded into the IP100A LF TxFIFO which specify bytes to be examined within received frames. A CRC is calculated over these bytes and compared with a CRC value supplied in the Pseudo Packet. If a match is found, the IP100A LF issues a Wake Event. The matching technique may result in false wake events being reported to the host system. Each Pseudo Packet consists of one or more byte-offset/byte-count pairs (or Pseudo Patterns), a terminator symbol, and a 4-byte CRC value. The byte offsets within the Pseudo Patterns indicate the number of received frame bytes to be skipped in order to reach the next group of bytes to be included in the CRC calculation. The byte-counts within the Pseudo Patterns indicate the number of bytes in the next group to be included in the CRC calculation. The terminator indicates the end of the Pseudo Patterns for the Pseudo Packet. Immediately following the terminator is a 4-byte CRC. If there is another Pseudo Packet, it will immediately follow the CRC value. The second Wake Event Data Structure is the Magic Packet. Magic Packets are uniquely formatted frames, which upon reception invoke a Wake Event by the IP100A LF. Once the IP100A LF has been placed in Magic Packet mode and put to sleep, it scans all incoming frames addressed to it for a data sequence consisting of a synchronization stream followed immediately by 16 consecutive repetitions of the station's own 48-bit Ethernet MAC station address. The sequence can be located anywhere within the received frame. The pseudo packet and Magic Packet data structures are shown in Figure 12
IP100A PseudoPattern 1 0x00 0x01 Ethernet Header Received Packet
PseudoPattern n pseudo packet Terminator
0x00+n-1 0x00+n 0x00+n+1 0x06 MagicSyncStream 0x00
PseudoCRC
Magic MagicSequence PacketTM
Ethernet CRC
FIGURE 12 : Wake Event Data Structures, Pseudo Packet and Magic Packet
40/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.3.1 MagicSequence Class............................. Wake Event Data Structures, Magic Packet Base Address ............... Start of Magic Packet Address Offset .............. 0x06 Access Mode ................ Read only Width ............................ 768 bits BIT 767..0 BIT NAME MagicSequence BIT DESCRIPTION Magic Sequence. A sequence of 96 bytes, consisting of 16 consecutive, identical 6 bytes sequences, where each 6 byte sequence equals the station address of the station receiving the Magic Packet.
11.3.2 MagicSyncStream Class............................. Wake Event Data Structures, Magic Packet Base Address ............... Start of Magic Packet Address Offset .............. 0x00 Access Mode ................ Read only Width ............................ 48 bits BIT 47..0 BIT NAME MagicSyncStream BIT DESCRIPTION Magic Packet Sync Stream. A stream of 6 bytes with the value 0xff indicates the start of the MagicSequence.
11.3.3 PseudoCRC Class............................. Wake Event Data Structures, Pseudo Packet Base Address ............... Start of Pseudo Packet Address Offset .............. 0x00+n+1 for n PseudoPatterns Access Mode ................ Write only Width ............................ 32 bits The 32-bit CRC as defined in the IEEE 802.3 Ethernet standard for the FCS, taken over the bytes (indicated by the PseudoPattern values) of a received frame. BIT 7..0 15..8 23..16 31..24 BIT NAME PsuedoCRCbyte0 PsuedoCRCbyte1 PsuedoCRCbyte2 PsuedoCRCbyte3 BIT DESCRIPTION The least significant byte of the PseudoCRC. The second lest significant byte of the PseudoCRC. The second most significant byte of the PseudoCRC. The most significant byte of the PseudoCRC.
41/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.3.4 PseudoPattern Class............................. Wake Event Data Structures, Pseudo Packet Base Address ............... Start of Pseudo Packet Address Offset .............. 0x00 thru 0x00+n-1 for nth PseudoPattern Access Mode ................ Write only Width ............................ 8 bits BIT 3..0 BIT NAME ByteCount BIT DESCRIPTION ByteCount can take on a value of 0x0 to 0xe. A value of 0xf indicates an extended value. The extended value will occupy 8 bits and is contained in the next PseudoPattern. If both the ByteOffset and the ByteCount values are 0xf, the next PseudoPattern will be the extended ByteOffset, and the PseudoPattern after that will be the extended ByteCount. ByteOffset can take on a value of 0x0 to 0xe. A value of 0xf indicates an extended value. The extended value will occupy 8 bits and is contained in the next PseudoPattern. If both the ByteOffset and the ByteCount values are 0xf, the next PseudoPattern will be the extended ByteOffset, and the PseudoPattern after that will be the extended ByteCount.
7..4
ByteOffset
11.3.5 Terminator Class............................. Wake Event Data Structures, Pseudo Packet Base Address ............... Start of Pseudo Packet Address Offset .............. 0x00+n for n PseudoPattern Access Mode ................ Write only Width ............................ 8 bits BIT 7..0 BIT NAME Terminator BIT DESCRIPTION A value of 0x00 indicates the end of the PseudoPattern.
42/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4 LAN I/O Registers The host interacts with the IP100A LF mainly through slave registers, which occupy 128 bytes in the host system's I/O space, memory space, or both. Generally, registers are referred to as "I/O registers", implying that the registers may in fact be mapped and accessed by the host system in memory space. I/O registers must be accessed with instructions that are no larger than the bit-width of that register. The IP100A LF LAN I/0 register layout is show in Figure 13. BYTE 3 BYTE 2 BYTE 1 BYTE 0 ADDR OFFSET 0x64 0x60 0x5C 0x58 0x54 MACCtrl0 IntEnable WakeEvent 0x50 0x4C 0x48 0x44 0x40 0x3C FIFOCtrl EepromCtrl AsicCtrl EepromData 0x38 0x34 0x30 0x2C 0x28 0x24 0x20 0x1C 0x18 RxDMAPollPeriod RxDMAUrgentThresh RxDMABurstThresh 0x14 0x10 0x0C TxDMABurstThresh 0x08 0x04 0x00
HashTable[63..32] HashTable[31..0] PhyCtrl MaxFrameSize MACCtrl1 IntStatus IntStatusAck TxStatus TxReleaseThresh ReceiveMode StationAddress[47..32]
StationAddress[31..0]
RxDMAListPtr RxDMAStatus TxDMAPollPeriod TxDMAUrgentThresh
TxDMAListPtr DMACtrl FIGURE 13 : IP100A LF I/O Register Map
43/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.1 AsicCtrl Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x30 Default .........................0x00004000 (default values for LED Speed, LED, Mode, PhySpeed10, PhySpeed100, PhyMedia are dependent on EEPROM settings, and ForcedConfig[1..0], ForcedCon-fig[2] are dependent on ED signal pin states) Width ............................ 32 bits AsicCtrl provides chip-specific, non-host-related settings. The contents of the least significant byte of AsicCtrl are read from EEPROM at reset. BIT 0 BIT NAME LEDFlashSpeed R/W R BIT DESCRIPTION The LED flahing Speed can be defined by this bit and could be set by EEPROM only. 0: Fast Speed (5ms, 35ms). 1: Low Speed (20ms, 60ms). The Bit decide LED Mode, could be set by EEPROM only. Light Emitting Diode Mode. LEDMode is used to control the LED signal pins functionality. When LEDMode is a logic 0 the LED signal pins operate in LED mode 0. When LEDMode is a logic 1 the LED signal pins operate in LED mode 1. Note: When LED Mode 0 is set, the period of 1 cycle alternating between logic 1/0 is 100ms. The LED ON period is 20ms and OFF period is 80ms. When LED Mode 1 is set, the period of 1 cycle alternating between logic 1/0 is 200ms. The LED ON period is 40ms and OFF period is 160ms. LED MODE 0 MODE 1 SIGNAL PIN LED_LINK This interface is not Continuous logic 0 when functioning under MODE 0 Ethernet link is valid. LED_10N Continuous logic 0 when Continuous logic 0 Ethernet link is operate at when Ethernet link is 10Mb/sec operate at 10Mb/sec LED_100N Continuous logic 0 when Continuous logic 0 Ethernet link is operate at when Ethernet link is 100Mb/sec operate at 100Mb/sec LED MODE 0 SIGNAL PIN LED_TXN Logic 0 indicates the frames are transmitting in progress, while logic 1 means no data is been sent. LED_RXN Logic 0 indicates the frames are been received. Logic 1 indicates no frame is MODE 1 Logic 0 indicates the link has established, while logic 1 indicates link is down. Alternating logic 1 and 0 indicates the transmission or receiving is in progress. Logic 0 indicates the link has established, while logic 1 indicates link is down. Alternating logic
March. 30, 2007 IP100A LF-DS-R17
1
LED Mode
R
44/97 Copyright (c) 2004, IC Plus Corp.
IP100A LF
Preliminary Data Sheet
BIT BIT NAME R/W BIT DESCRIPTION 1 and 0 indicates the data receiving is in progress. LED_DPLXN Logic 0 means the link is Logic 0 means the link established based on is established based on FULL Duplex Mode, FULL Duplex Mode, while logic 1 indicates while logic 1 indicates HALF Duplex Mode. HALF Duplex Mode. Alternating logic 1 and 0 indicates COLLISION has occurred. 2 TxLargeEnable R/W Transmit Large Frames Enable. If TxLargeEnable is a logic 1, the IP100A LF may transmit frames which are larger in size than the IP100A LF transmit FIFO. Receive Large Frames Enable. If RxLargeEnable is a logic 1, the IP100A LF may receive frames which are larger than the IP100A LF receive FIFO. Expansion ROM Disable. If ExpRomDisable is a logic 1, accesses to the on-adapter Expansion ROM are disabled and read to the Expansion ROM return 0x00000000 while writes to the Expansion ROM are ignored. Physical Device 10Mbps Capable. If PhySpeed10 is a logic 1, the IP100A LF PHY is capable of operating at 10Mbps. Physical Device 100Mbps Capable. If PhySpeed100 is a logic 1, the IP100A LF PHY is capable of operating at 100Mbps. Physical Device Media Type. If PhyMedia is a logic 0, copper media is in use. If PhyMedia is a logic 1, fiber media is in use. The combination of PhyMedia, PhySpeed100, and PhySpeed10 defines the capabilities of the PHY. PHY PHY PHY PHY CAPABILITY MEDIA SPEED100 SPEED10 0 0 0 Undefined 0 0 1 10BASE-T 0 1 0 100BASE-T 0 1 1 100BASE-T or 10BASE-T 1 0 0 Undefined 1 0 1 10BASE-F 1 1 0 100BASE-F 1 1 1 100BASE-F or 10BASE-F Forced Configuration. ForcedConfig[1..0] is used to enable and select a Forced Configuration mode for the IP100A LF. Forced Configuration mode is targeted toward embedded applications which do not utilize an EEPROM. In Forced Configuration mode, the IP100A LF is accessed via a PCI bus without first performing PCI configuration or loading parameters from an EEPROM. The ForcedConfig[1..0] bits 9 through 8 can also be set on reset using ED[4:3]. BIT 9 BIT 8 FORCED CONFIGURATION MODE 0 0 None 0 1 1
45/97
been received.
3
RxLargeEnable
R/W
4
ExpRomDisable
R/W
5 6 7
PhySpeed10 PhySpeed100 PhyMedia
R R R
9..8
ForcedConfig[1..0]
R/W
Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT BIT NAME R/W BIT DESCRIPTION 0 1 1 1 X Reserved In Forced Configuration mode 1, the IP100A LF is configured as follows: I/O base address = 0x200 I/O target cycles = enabled Memory target cycles = disabled Bus master cycles = enabled Expansion ROM cycles = disabled. 10 12..11 13 Reserved Reserved SpeedupMode N/A N/A R/W Reserved for future use. Reserved for future use. Speed Up Mode. SpeedupMode is used for simulation purposes only. When SpeedupMode is a logic 1 IP100A LF operation is modified to decrease simulation time. SpeedupMode can also be set on reset using signal pin 20. Reserved for future use. Global Reset. When GlobalReset is a logic 1, the IP100A LF resets the logic functions and registers specified by the DMA, FIFO, Network, Host, and AutoInit bits (related to both the transmit and receive processes as applicable). The LAN PCI Configuration Registers are not affected by GlobalReset. GlobalReset is self-clearing. Receive Reset. When RxReset is a logic 1 the IP100A LF resets all of the receive logic functions and registers specified by the DMA, FIFO, and Network bits. RxReset is self-clearing, and should not be used after initialization except to recover from receive errors such as a receive FIFO over run. Transmit Reset. When TxReset is a logic 1 the IP100A LF resets all of the transmit logic functions and registers specified by the DMA, FIFO, and Network bits. TxReset is self clearing, and is required to be used after a transmit underrun error. DMA Reset. DMA selects (when a logic 1) or excludes (when a logic 0) the IP100A LF DMA functions and registers (see below) for/from reset based on the value of the GlobalReset, RxReset, and TxReset bits. The DMA bit is self-clearing. FIFO Reset. FIFO selects (when a logic 1) or excludes (when a logic 0) the IP100A LF FIFO functions and registers for/from reset based on the value of the GlobalReset, RxReset, and TxReset bits. The FIFO bit is self-clearing. Network Reset. Network selects (when a logic 1) or excludes (when a logic 0) the IP100A LF network functions and registers for/from reset based on the value of the GlobalReset, RxReset, and TxReset bits. The Network bit is self-clearing. Automatic Initialization Reset. AutoInit selects (when a logic 1) or excludes (when a logic 0) the IP100A LF auto-initialization logic function for/from re-loading IP100A LF parameters from an EEPROM based on the value of the GlobalReset bit. The AutoInit bit is self-clearing.
46/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
14 15 16
Reserved Reserved GlobalReset
N/A N/A W
17
RxReset
W
18
TxReset
W
19
DMA
W
20
FIFO
W
21
Network
W
23
AutoInit
W
IP100A LF
Preliminary Data Sheet
BIT 24 25 BIT NAME Reserved InterruptRequest R/W N/A W BIT DESCRIPTION Reserved for future use. Interrupt Request. When InterruptRequest is a logic 1, the IntRequested bit of the IntStatus register is set to a logic 1. InterruptRequest is self-clearing. Reset Busy. When ResetBusy is a logic 1 a reset process is in progress. After asserting a reset using the GlobalReset, RxReset, or TxReset bits, the ResetBusy bit must be polled (or periodically read) until it is a logic 0 indicating the reset operation is complete. Reserved for future use.
26
ResetBusy
R/W
31..27
Reserved
N/A
47/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.2 DMACtrl Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x00 Default .......................... 0x00000000 Width ............................ 32 bits DMACtrl controls some of the bus master functions in the receive DMA and transmit DMA logic, and contains status bits. DMACtrl is cleared by a reset. BIT 0 BIT NAME RxDMAHalted R/W R BIT DESCRIPTION Receive DMA Halted. RxDMAHalted is a logic 1 whenever receive DMA is halted by setting RxDMAHalt or an implicit halt due to fetching a RFD with RxDMAComplete in RxFrameStatus already a logic 1. RxDMAHalted is cleared by setting RxDMAResume to a logic 1. Transmit DMA Complete Request. TxDMACmplReq is equivalent to the TxDMAIndicate field in the TxFrameControl of the current TFD. Transmit DMA Halted. TxDMAHalted is a logic 1whenever transmit DMA is halted by setting TxDMAHalt. TxDMAHalted is cleared by setting TxDMAResume to a logic 1. Receive DMA Complete. RxDMAComplete is equivalent to the RxDMAComplete bit in the IntStatus register. RxDMAComplete is different from the RxDMAComplete bit in RxDMAStatus. RxDMAComplete is latched once a frame receive DMA transfer has completed. RxDMAComplete is cleared by acknowledging the RxDMAComplete bit in the IntStatus register. TxDMAComplete. TxDMAComplete is the same as the TxDMAComplete bit in IntStatus register. TxDMAComplete is cleared by acknowledging the TxDMAComplete bit in the IntStatus register. Reserved for future use. Receive DMA Halt. If RxDMAHalt is a logic 1, the receive DMA is halted. RxDMAHalt is self-clearing and writing a 0 is ignored. See RxDMAHalted to determine the running state of receive DMA. Receive DMA Resume. If RxDMAResume is a logic 1, the receive DMA is resumed. RxDMAResume is self-clearing and writing a 0 is ignored. See RxDMAHalted to determine the running state of receive DMA. Transmit DMA Halt. If TxDMAHalt is a logic 1, the transmit DMA is halted. TxDMAHalt is self-clearing and writing a 0 is ignored. See TxDMAHalted to determine the running state of transmit DMA. Transmit DMA Resume. If TxDMAResume is a logic 1, the transmit DMA is resumed. TxDMAResume is self-clearing and writing a 0 is ignored. See TxDMAHalted to determine the running state of transmit DMA. Reserved for future use.
1
TxDMACmplReq
R
2
TxDMAHalted
R
3
RxDMAComplete
R
4
TxDMAComplete
R
7..5 8
Reserved RxDMAHalt
N/A W
9
RxDMAResume
W
10
TxDMAHalt
W
11
TxDMAResume
R/W
13..12
Reserved
N/A
48/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 14 BIT NAME TxDMAInProg R/W R BIT DESCRIPTION Transmit DMA in Progress. If TxDMAInProg is a logic 1, a transmit DMA operation is in progress. TxDMAInProg is primarily used by the host system in an under run recovery routine. The host system waits for TxDMAInProg to be a logic 0 before setting the TxReset bit of the AsicCtrl register to clear the under run condition. Before checking TxDMAInProg, issue TxDMAHalt. DMA Halt Busy. DMAHaltBusy indicates that a DMA Halt operation (TxDMAHalt or RxDMAHalt) is in progress and the host system should wait for DMAHaltBusy to be cleared before performing other actions. Reserved for future use. Reserved for future use. Reserved for future use. Reserved for future use. PCI MWI Command Disable. If Setting MWIDisable is a logic 1, the IP100A LF will not use the Memory Write Invalidate (MWI) PCI command. Reserved for future use. Receive DMA Overrun Frame. If RxDMAOverrunFrame is a logic 0, receive DMA will discard receive overrun frames without transferring them to the host system. WhenRxDMAOverrunFrame is a logic 1, receive DMA will transfer overrun frames to the host system. Overrun frames are any frame which is received while the receive FIFO is full. Reserved for future use. Bus Target Abort. TargetAbort is a logic 1 when the IP100A LF experiences a target abort sequence when operating as a bus master. TargetAbort indicates a fatal error, and must be cleared before further transmit DMA or receive DMA operation can proceed. TargetAbortt is cleared via the GlobalReset, and DMA bits of the AsicCtrl register. Bus Master Abort. MasterAbort is a logic 1 when the IP100A LF experiences a master abort sequence when operating as a bus master. MasterAbort indicates a fatal error, and must be cleared before further transmit DMA or receive DMA operation can proceed. MasterAbortt is cleared via the GlobalReset, and DMA bits of the AsicCtrl register.
15
DMAHaltBusy
R
16 17 18 19 20
Reserved Reserved Reserved Reserved MWIDisable
N/A N/A N/A N/A R/W
21 22
Reserved RxDMAOverrunFrame
N/A R/W
29..23 30
Reserved TargetAbort
N/A R
31
MasterAbort
R
49/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.3 EepromCtrl Class............................. LAN I/O Registers, External Interface Control Base Address ............... IoBaseAddress register value Address Offset .............. 0x36 Default .......................... 0x0000 Width ............................ 16 bits BIT 5:0 BIT NAME EepromAddress R/W R/W BIT DESCRIPTION EEPROM Address. EepromAddress identify one of the 256, sixteen-bit words to be the target for the ReadRegister, WriteRegister or EraseRegister commands. Bits 7 and 6 are further defined to identify a sub-command based on the value of EepromOpcode. The definition of bits 7 and 6 are valid when the EepromOpcode in bits 9 and 8 equals 00. BIT 7 BIT 6 SUB-COMMAND 0 0 WriteDisable 0 1 WriteAII 1 0 EraseAll 1 1 WriteEnable EEPROM Operation Code. EepromOpcode specifies one of three individual commands and a single group of four sub-commands. If both bit 9 and bit 8 are logic zero, the Opcode function will be based on the value in bit 6 and bit 7, otherwise bit 6 and bit 7 does not have any affect to these 2 bits. BIT 9 BIT 8 OPCODE COMMAND 0 0 Don't Care 0 1 WriteRegister 1 0 ReadRegister 1 1 Don't Care Note, after every WriteRegister, EraseRegister opcode, or WriteAll or EraseAll subcommand, the IP100A LFwill automatically issue a WriteDisable command to the EEPROM. Therefore, a WriteEnable command must be issued to the EEPROM prior to every WriteRegister, EraseRegister opcode, or WriteAll or EraseAll subcommand. Reserve for future use R/W When the 93C46TypSel is logic 1, IP100A LF accesses the 93C46 EEPROM by normal address code. And when this bit is set to logic 0, IP100A LF read/write the 93C46 EEPROM via special address code. This function is designed for special usage only. EEPROM Select. If this bit is logic 0, it means that IP100A LF is connected to 93C46 series EEPROM. Read back as 1. EEPROM Busy. EepromBusy is a logic 1 during the execution of EEPROM commands. Further commands should not be issued to EepromCtrl nor should data be read from Eeprom-Data while EepromBusy is a logic 1.
7:6
EepromCommand
R/W
9..8
EepromOpcode
R/W
10..11 12
Reserved 93C46TypeSel
13 14 15
EepromSel Reserved EepromBusy
RO RO R
50/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.4 EepromData Class............................. LAN I/O Registers, External Interface Control Base Address ............... IoBaseAddress register value Address Offset .............. 0x34 Default .......................... 0x0000 Width ............................ 16 bits EepromData is a 16-bit data register for use with the adapter's serial EEPROM. Data from the EEPROM should be read by the host system from EepromData register based on the state of the EepromBusy bit of the EepromCtrl register. Data to be written to the EEPROM is written to EepromData prior to issuing the write command to EepromCtrl. BIT 15..0 BIT NAME EepromData R/W R/W BIT DESCRIPTION EEPROM Data. Data read from, or to be written to, the external EEPROM.
11.4.5 FIFOCtrl Class............................. LAN I/O Registers, FIFO Control Base Address ............... IoBaseAddress register value Address Offset .............. 0x3a Default .......................... 0x0000 Width ............................ 16 bits FIFOCtrl provides various control and indications for the transmit FIFO and the receive FIFO diagnostic. BIT 0 8..1 9 BIT NAME RAMTest Mode Reserved RxOverrunFrame R/W R/ W N/A R/ W BIT DESCRIPTION RAM Tes t Mode. I f RAMTestMode is a logic 1, the FIFO RAM is in the test mode. Reserved for future use. Receive Overrun Frame. RxOverrunFrame determines how the IP100A LF handles receive overrun frames. If RxOverrunFrame is a logic 0, the IP100A LF discards all overrun frames. If RxOverrunFrame is a logic 1, the IP100A LF will retain all overrun frames, so that they may be inspected by the host for diagnostic purposes. Reserved for future use. Receive FIFO Full. If RxFIFOFull is a logic 1, the receive FIFO is full. RxFIFOFull does not in itself indicate an overrun condition. However, if more data is received while RxFIFOFull is a logic 1, an overrun will occur. RxFIFOFull is cleared as soon as the receive FIFO is no longer full. Reserved for future use. Transmit Indicator. Transmitting is set to a logic 1 whenever a frame is being transmitted or during a transmit deferral). Receive Indicator. Receiving is set to a logic 1 whenever a frame is being received. No action is expected on the part of the host based on the state of Receiving.
10 11
Reserved RxFIFOFull
N/A R
13..12 14 15
Reserved Transmitting Receiving
N/A R R
51/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.6 HashTable Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x66, 0x64, 0x62, 0x60 Default .......................... 0x0000000000000000 Width ............................ 64 bits (accessible as 4, 16 bit words) The host system stores a 64-bit hash table in this register for selectively receiving multicast frames. Setting the ReceiveMulticastHash bit in ReceiveMode register enables the filtering mechanism. BIT 15..0 31..16 47..32 63..48 BIT NAME HashTableWord0 HashTableWord1 HashTableWord2 HashTableWord3 R/W R/W R/W R/W R/W BIT DESCRIPTION The least significant word of the hash table, corresponding to address 0x60. The second least significant corresponding to address 0x62. The second most significant corresponding to address 0x64. word word of of the the hash hash table, table,
The most significant word of the hash table, corresponding to address 0x66.
The IP100A LF applies a cyclic-redundancy-check (the same CRC used to calculate the frame data FCS) to the destination address of all incoming multicast frames (with multicast bit set). The low-order 6 bits of the CRC result are used as an addressing index into the hash table. The MSB of HashTable[3] is the most significant bit, and the LSB of HashTable[0] is the least significant bit, addressed by the 6-bit index. If the HashTable bit addressed by the index is a logic 1, the frame is accepted by the IP100A LF and transferred to higher layers. If the addressed hash table bit is a logic 0, the frame is discarded. 11.4.7 IntEnable Class............................. LAN I/O Registers, Interrupt Base Address ............... IoBaseAddress register value Address Offset.............. 0x4c Default .......................... 0x0000 Width ............................ 16 bits Enables individual interrupts as specified in the IntStatus register. Setting a bit in IntEnable will allow the specific source to generate an interrupt on the PCI bus. IntEnable is cleared by a read of IntStatusAck. BIT 0 1 2 3 4 5 6 BIT NAME Reserved EnHostError EnTxComplete R/W N/A R/W R/W BIT DESCRIPTION Reserved for future use. Enable Host Error Interrupt. Enables the HostError interrupt. Enable Transmit Complete Interrupt. Enables the TxComplete interrupt. Enable MAC Control Frame Interrupt. Enables the MACControlFrame interrupt. Enable Receive Complete Interrupt. Enables the RxComplete interrupt. Reserved for future use. Enable Interrupt Requested Interrupt. Enables the IntRequested interrupt.
52/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
EnMACControlFrame R/W EnRxComplete Reserved EnIntRequested R/W R/W R/W
IP100A LF
Preliminary Data Sheet
BIT 7 8 9 10 11 15..12 BIT NAME EnUpdateStats EnLinkEvent R/W R/W R/W BIT DESCRIPTION Enable Update Stats Interrupt. Enables the UpdateStats interrupt. Enable Link Event Interrupt. Enables the LinkEvent interrupt. Enable Transmit DMA Complete TxDMAComplete interrupt. Enable Receive DMA Complete RxD-MAComplete interrupt. Reserved for future use. Reserved for future use. Interrupt. Interrupt. Enables Enables the the
EnTxDMAComplete R/W EnRxDMAComplete R/W Reserved Reserved N/A N/A
11.4.8 IntStatus Class............................. LAN I/O Registers, Interrupt Base Address ............... IoBaseAddress register value Address Offset .............. 0x4e Default .......................... 0x0000 Width ............................ 16 bits IntStatus indicates the source of interrupts and indications on the IP100A LF. All bits except InterruptStatus are the interrupt causing sources for the IP100A LF. Each interrupt source can be individually disabled using the IntEnable register. The host system may acknowledge most interrupts by writing a logic 1 into the corresponding IntStatus bit, which will cause the IP100A LF to clear the interrupt indication. BIT 0 BIT NAME InterruptStatus R/W R/W BIT DESCRIPTION Interrupt Status. InterruptStatus is a logic 1 when the IP100A LF is driving the bus interrupt signal (INTAN). InterruptStatus is a logical OR of all the interrupt causing sources after they have been filtered through the IntEnable register. Host Error Interrupt. HostError is a logic 1 when a catastrophic error related to the bus interface occurs. Catastrophic bus interface errors include PCI target abort and PCI master abort. A HostError interrupt requires a setting the GlobalReset and DMA bits of the AsicCtrl register. Transmit Complete. TxComplete is a logic 1 when a frame whose TxIndicate bit in the TFD's TxFrameControl field is a logic 1, has been successfully transmitted or for any frame that experiences a transmission error. A TxComplete interrupt requires writing to TxStatus register to advance the status queue. MAC Control Frame Received Interrupt. MACControlFrame is a logic 1 when a MAC Control frame has been received by the IP100A LF. Receive Complete Interrupt. RxComplete is a logic 1 when one or more entire frames have been received into the receive FIFO. RxComplete is automatically acknowledged by the receive DMA logic as it transfers frames. Reserved for future use.
1
HostError
R/W
2
TxComplete
R/W
3
MACControlFrame
R/W
4
RxComplete
R/W
5
Reserved
R/W
53/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 6 BIT NAME IntRequested R/W R/W BIT DESCRIPTION Interrupt Requested Interrupt. IntRequested is a logic 1 after the host system requests an interrupt by setting InterruptRequest bit of the AsicCtrl register. Update Statistics Interrupt. UpdateStats is a logic 1 to indicate that one or more of the statistics registers is nearing an overflow condition (typically half of its maximum value). The host system should respond to an UpdateStats interrupt by reading all of the statistic registers, thereby acknowledging and clearing UpdateStats bit. Link Event Interrupt. LinkEvent is a logic 1 to indicate a change in the state of the Ethernet link. Transmit DMA Complete Interrupt. TxDMAComplete is a logic 1 to indicate that a transmit DMA operation has completed, and the frame's corresponding TFD had the TxDMAComplete bit in the TxFrameControl field set to a logic 1. Receive DMA Complete Interrupt. RxDMAComplete is a logic 1 to indicate that a frame receive DMA operation has completed. Reserved for future use. Reserved for future use.
7
UpdateStats
R/W
8 9
LinkEvent TxDMAComplete
R/W R/W
10 11 15..12
RxDMAComplete Reserved Reserved
R/W N/A N/A
11.4.9 IntStatusAck Class............................. LAN I/O Registers, Interrupt Base Address ............... IoBaseAddress register value Address Offset .............. 0x4a Default .......................... 0x0000 Width ............................ 16 bits IntStatusAck is another version of the IntStatus register, having the same bit definition as IntStatus, but providing additional functionality to reduce the number of I/O operations required to perform common tasks related to interrupt handling. In addition to returning the IntStatus value, when read IntStatusAck also acknowledges the TxDMAComplete, RxDMAComplete, IntRequested, MACControlFrame, and LinkEvent interrupt bits within the IntStatus register (if they are set), and clears the IntEnable register (preventing subsequent events from generating an interrupt). BIT 0 1 2 3 4 5 6 7 8 9 10 BIT NAME InterruptStatus HostError TxComplete MACControlFrame RxComplete Reserved IntRequested UpdateStats LinkEvent TxDMAComplete RxDMAComplete R/W R R R R R R R R R R R BIT DESCRIPTION See InterruptStatus in the IntStatus register. See HostError in the IntStatus register. See TxComplete in the IntStatus register. See MACControlFrame in the IntStatus register. See RxComplete in the IntStatus register. Reserved for future use. See IntRequested in the IntStatus register. See UpdateStats in the IntStatus register. See LinkEvent in the IntStatus register. See TxDMAComplete in the IntStatus register. See RxDMAComplete in the IntStatus register.
54/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 11 15..12 BIT NAME Reserved Reserved R/W N/A N/A BIT DESCRIPTION Reserved for future use. Reserved for future use.
11.4.10 MACCtrl0 Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x50 Default .......................... 0x0000 Width ............................ 16 bits BIT 1..0 BIT NAME IFSSelect R/W R/W BIT DESCRIPTION Inter-Frame Spacing Select. IFSSelect indicates the minimum number of bit times between the end of one Ethernet frame, and the beginning of another when the IP100A LF is deferring after a collision with the IP100A LF the last device to successfully acquire the network (in half duplex mode). By selecting a large value for IFSSelect, the IP100A LF will become less "aggressive" on the network and may defer more often (preventing the IP100A LF from "capturing" the network). The performance of the IP100A LF may decrease as the IFSSelect value is increased from the standard value. BIT1 BIT0 INTER-FRAME SPACING IN BIT TIMES 0 0 96 (802.3 standard value, and default) 0 1 128 1 0 224 1 1 544 Reserved for future use. Full Duplex Enable. Setting FullDuplexEnable to a logic 1 configures the IP100A LF to function in a full duplex manner. When operating in full duplex, the IP100A LF disables transmitter deference to receive traffic, allowing simultaneous receive and transmit traffic. Operation in full duplex has the side-effect of disabling CarrierSenseErrors statistics collection, since full duplex operation requires carrier sense to be masked to the transmitter. TxReset and RxReset bits in AsicCtrl must be set for changes ofFullDuplexEnable to take effect. Receive Large Frames. RcvLargeFrames determines the frame size at which the RxOversizedFrame bit of the RxFrameStatus field is set for receive frames. When RcvLargeFrames is a logic 0, minimum OversizedFrame size is 1514 bytes. When RcvLargeFrames is set, minimum OversizedFrame size is 4491 bytes. (This value was the maximum FDDI frame size of 4500 bytes, subtracting bytes for fields that have no Ethernet equivalent.) The frame size at which an OversizedFrame error will be flagged includes the destination and source addresses, the type/length field, and the FCS field. Reserved for future use.
4..2 5
Reserved FullDuplexEnable
N/A R/W
6
RcvLargeFrames
R/W
7
Reserved
N/A
55/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 8 BIT NAME FlowControlEnable R/W R/W BIT DESCRIPTION Flow Control Enable. If FlowControlEnable is a logic 0, the IP100A LF treats all incoming frames as data frames. If FlowControlEnable is a logic 1, flow control is enabled and the IP100A LF will act upon incoming flow control PAUSE frames. If FlowControlEnable is a logic 1, FullDuplexEnable should also be set to a logic 1. Receive FCS. If RcvFCS is a logic 1, the IP100A LF will include the receive frame's FCS along with the frame data transferred to the host system. If RcvFCS is a logic 0, the IP100A LF will remove the FCS from the frame before transferring the frame to the host system. The state of RcvFCS does not affect the IP100A LF's checking of the frame's FCS and its posting of FCS errors. RcvFCS should only be changed when the receiver is disabled (via the RxDisable bit of the MACCtrl1 register) and after resetting the receive FIFO (via the FIFO bit of the AsicCtrl register). FIFO Loopback. If FIFOLoopback is a logic 1, the IP100A LF will enter FIFO Loopback Mode and force data to loopback from the transmit FIFO directly into the receive FIFO. When using FIFO Loopback Mode, it is the host system's responsibility to ensure that proper interframe spacing is ensured. To accommodate proper interframe spacing, the host system must not load more than one transmit frame into the transmit FIFO at a time while in FIFO Loopback Mode. The TxReset and RxReset bits of the AsicCtrl register must be set after changing the value of FIFOLoopback. MAC Loopback. If MACLoopback is a logic 1, the IP100A LF will enter MAC Loopback Mode and force data to loopback from the MAC transmit interface to the MAC receive interface. The TxReset and RxReset bits in AsicCtrl register must be set after changing the value of MACLoopback. Reserved for future use.
9
RcvFCS
R/W
10
FIFOLoopback
R/W
11
MACLoopback
R/W
15..12
Reserved
N/A
Note: External loopback is controlled by the PHY. To utilize external loopback, the host system must enable a loopback mode within the PHY using the MII Management Interface. For the true "on-the-wire" loopback mode, use a loopback plug (connector), clear the FIFOLoopback, and MACLoopback and any PHY loopback bits to zero, set the FullDuplexEnable bit to a logic 1, and enable the full duplex mode within the PHY. 11.4.11 MACCtrl1 Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x52 Default .......................... 0x0000 Width ............................ 16 bits BIT 0 1 BIT NAME CollisionDetect CarrierSense R/W R R BIT DESCRIPTION Collision Detect. CollisionDetect provides a real-time indication of the state of the COL signal within the IP100A LF. Carrier Sense. CarrierSense provides a real-time indication of the state of the CRS signal within IP100A LF.
56/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 2 BIT NAME TxInProg R/W R BIT DESCRIPTION Transmit In Progress. TxInProg provides a real-time indication that a frame is being transmitted. If TxInProg is a logic 1, a frame transmission is in progress. TxInProg is used by the host system during under run recovery to delay before setting the issuing a TxReset bit in the AsicCtrl register. Transmit Error. If a transmit under run occurs (indicated via the TxUnderrun bit of the TxStatus register), TxError is a logic 1, indicating that the transmitter needs to be reset via the TxReset bit in the AsicCtrl register. Reserved for future use. Statistics Enable. Writing a logic 1 to StatisticsEnable will enable the IP100A LF's statistic registers. The state (enabled/disabled) of the IP100A LF's statistic registers is shown via StatisticsEnabled. Statistics Disable. Writing a logic 1 to StatisticsDisable will disable the IP100A LF's statistic registers. The state (enabled/disabled) of the IP100A LF's statistic registers is shown via StatisticsEnabled. Statistics Enabled. If StatisticsEnabled is a logic 1, the IP100A LF's statistic registers are enabled. Transmit Enable. Writing a logic 1 to TxEnable will enable the IP100A LF to transmit frames. The state (enabled/disabled) of the IP100A LF's transmitter is shown via TxEnabled. Transmit Disable. Writing a logic 1 to TxDisable will disable the IP100A LF from transmitting frames. The state (enabled/disabled) of the IP100A LF's transmitter is shown via TxEnabled. Transmit Enabled. If TxEnabled is a logic 1, the IP100A LF's transmitter is enabled. Receive Enable. Writing a logic 1 to RxEnable will enable the IP100A LF to receive frames. The state (enabled/disabled) of the IP100A LF's receiver is shown via RxEnabled. Receive Disable. Writing a logic 1 to RxDisable will disable the IP100A LF from receiving frames. The state (enabled/disabled) of the IP100A LF's receiver is shown via RxEnabled. Receive Enabled. If RxEnabled is a logic 1, the IP100A LF's receiver is enabled. Paused. If Paused is a logic 1, the IP100A LF has received a PAUSE MAC Control Frame and the IP100A LF has halted the transmitter for the duration indicated in the PAUSE Frame's pause_time field. Paused will become a logic 0 when the IP100A LF's transmitter ends is pause operation. Reserved for future use.
3
TxError
R
4 5
Reserved StatisticsEnable
N/A W
6
StatisticsDisable
W
7 8
StatisticsEnabled TxEnable
R W
9
TxDisable
W
10 11
TxEnabled RxEnable
R W
12
RxDisable
W
13 14
RxEnabled Paused
R R
15
Reserved
N/A
57/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.12 MaxFrameSize Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset.............. 0x5a Default .......................... 0x1514 or 0x4491 based on the RcvLargeFrames bit in the MACCtrl0 register Width ............................ 16 bits BIT 15..0 BIT NAME MaxFrameSize R/W R/W BIT DESCRIPTION Maximum Frame Size. Received frames with sizes equal to or larger than MaxFrameSize will be flagged as oversize via the RxOversizedFrame bit in RxDMAStatus field of the frame's RFD.
11.4.13 PhyCtrl Class............................. LAN I/O Registers, External Interface Control Base Address ............... IoBaseAddress register value Address Offset .............. 0x5e Default .......................... 0x00 Width ............................ 8 bits PhyCtrl contains control bits for the internal MII Management Interface. The MII Management Interface is used to access registers in the IP100A LF PHY. The host system accesses the MII Management Interface by writing and reading bit patterns to the PhyCtrl register. BIT 0 1 BIT NAME MgmtClk MgmtData R/W R/W R/W BIT DESCRIPTION Management Clock. MgmtClk drives the management clock (MDC) signal to the PHY. Management Data bit. MgmtData is directly connected to the MDIO signal connected to the PHY. Data can be written to or read from the PHY by writing or read MgmtData based on the value of MgmtDir. Management Data Direction. If the MgmtDir is a logic 1, the value written to MgmtData is driven onto the MDIO signal connected to the PHY. When MgmtDir is a logic 0, data driven onto MDIO by the PHY can be read from MgmtData. Reserved for future use. PHY Duplex Polarity. If PhyDuplexPolarity is a logic 0, the duplex status signal between the PHY and the MAC is active low. PHY Duplex Status. If PhyDuplexStatus is a logic 1, the PHY is operating in full duplex mode. If PhyDuplexStatus is a logic 0, the PHY is operating in half duplex mode. PHY Speed Status. PhySpeedStatus provides a real-time indication of the IP100A LF's PHY speed. If PhySpeedStatus is a logic 1, the IP100A LF's PHY is operating at 100Mbps operation. If PhySpeedStatus is a logic 0, the IP100A LF's PHY is operating at 10Mbps operation. PHY Link Status. PhyLinkStatus provides a real-time indication of the IP100A LF's PHY link state. If PhyLinkStatus is a logic 1, the IP100A LF's PHY link is up. If PhyLinkStatus is a logic 0, the IP100A LF's PHY link is down.
58/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
2
MgmtDir
R/W
3 4 5
Reserved PhyDuplexPolarity PhyDuplexStatus
N/A R/W R
6
PhySpeedStatus
R
7
PhyLinkStatus
R
IP100A LF
Preliminary Data Sheet
11.4.14 ReceiveMode Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x5c Default .......................... 0x00 Width ............................ 8 bits ReceiveMode sets the receive filter of the IP100A LF. BIT 0 BIT NAME ReceiveUnicast R/W R/W BIT DESCRIPTION Receive Unicast. If ReceiveUnicast is a logic 1, the IP100A LF receives unicast frames (frames where the DA field matches the 48-bit value in the StationAddress register. Receive Multicast. If ReceiveMulticast is a logic 1, the IP100A LF receives all multicast frames, including broadcast frames. Receive Broadcast. If ReceiveBroadcast is a logic 1, the IP100A LF receives all broadcast frames. Receive All Frames. If ReceiveAllFrames is a logic 1, the IP100A LF receives all frames. Receive Multicast Hash. If ReceiveMulticastHash is a logic 1, the IP100A LF receives all which pass the hash filtering mechanism defined in the HashTable register.. Receive IP Multicast. If ReceiveIPMulticast is a logic 1, the IP100A LF receives all multicast IP datagrams, which are mapped into Ethernet multicast frames with destination address of 01:00:5e:xx:xx:xx as defined in RFC 1112 and RFC 1700. The first 3 bytes require exact match, and the last 3 bytes are ignored. Reserved for future use.
1 2 3 4
ReceiveMulticast ReceiveBroadcast ReceiveAllFrames ReceiveMulticastHash ReceiveIPMulticast
R/W R/W R/W R/W
5
R/W
7..6
Reserved
N/A
11.4.15 RxDMABurstThresh Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x14 Default .......................... 0x08 Width ............................ 8 bits RxDMABurstThresh register sets the threshold for receive DMA bus master requests by the IP100A LF based upon the number of used bytes in the receive FIFO, in units of 32 bytes. When the used space exceeds the threshold, the IP100A LF may make a receive DMA request on the PCI bus. However, if the used space exceeds the RxDMAFrameLen field in the current RFD, the IP100A LF will make receive DMA bus request regardless of whether the used space exceeds the RxDMABurstThresh or not. RxDMABurstThresh may be overridden by the urgent request mechanism. See the PCI Bus Master Operation section for information about the relationship between RxDMABurstThresh and RxDMAUrgentThresh. Any value less than 0x08 is invalid and is interpreted as 0x08. BIT 7..0 BIT NAME R/W BIT DESCRIPTION Receive DMA Burst Threshold. The RxDMABurstThresh is the of 32 byte words which must be present in the receive FIFO prior to the assertion of a receive DMA bus master request.
RxDMABurstThresh R/W
59/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.16 RxDMAListPtr Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x10 Default .......................... 0x00000000 Width ............................ 32 bits RxDMAListPtr is the physical address of the current receive DMA Frame Descriptor in the Receive DMA List. A value of 0x00000000 for RxDMAListPtr indicates that no more RFDs are available to accept receive frames. RxDMAListPtr only points to addresses on 8-byte boundaries, so RFDs must be aligned on 8-byte physical address boundaries. RxDMAListPtr may be written directly by the host system to point the IP100A LF to the head of a newly created Receive DMA List. RxDMAListPtr is also updated by the IP100A LF as it processes RFDs in the Receive DMA List. As the IP100A LF finishes processing a RFD, it loads RxDMAListPtr with the value from the RxDMANextPtr field of the current RFD in order to move on to the next RFD in the Receive DMA List. If the IP100A LF loads a value of 0x00000000 from the current RFD, the receive DMA logic enters the idle state, waiting for a non-zero value to be written to RxDMAListPtr. To avoid access conflicts between the IP100A LF and the host system, the host system must set the RxDMAHalt bit in the DMACtrl register before writing to RxDMAListPtr. BIT 31..0 BIT NAME RxDMAListPtr R/W R/W BIT DESCRIPTION Receive DMA List Pointer. RxDMAListPtr is the physical address, on a 8-byte boundary, of the current RFD in the Receive DMA List.
11.4.17 RxDMAPollPeriod Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x16 Default .......................... 0x00 Width ............................ 8 bits RxDMAPollPeriod determines the rate at which the current RFD's RxDMAComplete bit of the RxFrameStatus field in the RFD is polled for a logic 0. Polling is disabled when RxDMAPollPeriod is 0x00. RxDMAPollPeriod is specified in increments of 320 ns. The maximum value is 127 (or 40.64 us). BIT 6..0 BIT NAME RxDMAPollPeriod R/W R/W BIT DESCRIPTION Receive DMA Poll Period. RxDMAPollPeriod is the number of 320ns intervals between polls of the RxDMAComplete bit in the RxFrameStatus field of the current RFD. Reserved for future use.
7
Reserved
N/A
11.4.18 RxDMAStatus Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x0c Default .......................... 0x00000000 Width ............................ 32 bits RxDMAStatus shows the status of various operations in the receive DMA logic. Host systems should read RxDMAStatus only if the RxDMAHalted bit in the DMACtrl register is a logic 1. Otherwise the IP100A LF may change RFDs between accesses to RxDMAStatus. Many bits of RxDMAStatus are identical to corresponding bits of the RxFrameStatus field.
60/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 12..0 BIT NAME RxDMAFrameLen R/W R BIT DESCRIPTION Receive DMA Frame Length.RxDMAFrameLen is similar to the RxDMAFrameLen bit of the RxFrameStatus field, except that RxDMAFrameLen provides a real-time indication of the number of bytes transferred during a receive DMA operation. Reserved for future use. See the RxFrameError bit of the RxFrameStatus field. See the RxDMAComplete bit of the RxFrameStatus field. See the RxFIFOOverrun bit of the RxFrameStatus field. See the RxRuntFrame bit of the RxFrameStatus field. See the RxAlignmentError bit of the RxFrameStatus field. See the RxFCSError bit of the RxFrameStatus field. See the RxOversizedFrame bit of the RxFrameStatus field. Reserved for future use. See the DribbleBits bit of the RxFrameStatus field. See the RxDMAOverflow bit of the RxFrameStatus field. Reserved for future use.
13 14 15 16 17 18 19 20 22..21 23 24 31..25
Reserved RxFrameError RxDMAComplete RxFIFOOverrun RxRuntFrame RxAlignmentError RxFCSError RxOversizedFrame Reserved DribbleBits RxDMAOverflow Reserved
N/A R R R R R R R N/A R R N/A
11.4.19 RxDMAUrgentThresh Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x15 Default .......................... 0x04 Width ............................ 8 bits RxDMAUrgentThresh sets a threshold at which the receive DMA logic will make a urgent bus master request. A urgent receive DMA request will have priority over all other requests on the IP100A LF. The urgent bus request is made when the free space in the receive FIFO falls below the value in RxDMAUrgentThresh. A receive DMA urgent request is not subject to the RxDMABurstThresh constraint. When the receive FIFO is close to overrun, burst efficiency is sacrificed in favor of requesting the bus as quickly as possible. The value in RxDMAUrgentThresh represents free space in the receive FIFO in terms of 32-byte portions. BIT 4..0 BIT NAME R/W BIT DESCRIPTION Receive DMA Urgent Threshold. RxDMAUrgentThresh is the minimum number of 32-byte words which must be available in the receive FIFO to avoid a receive DMA urgent request. Reserved for future use.
RxDMAUrgentThresh R/W
7..5
Reserved
N/A
61/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.20 StationAddress Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x54, 0x56, 0x58 Default .......................... 0x000000000000 Width ............................ 48 bits (accessible as 3, 16 bit words) StationAddress is used to define the individual destination address that the IP100A LF will respond to when receiving frames. Network addresses are generally specified in the form of 01:23:45:67:89:ab, where the bytes are received left to right, and the bits within each byte are received right to left (Isb to msb). The actual transmitted and received bits are in the order of 10000000 11000100 10100010 11100110 10010001 11010101. BIT 15..0 31..16 47..32 BIT NAME StationAddressWord0 StationAddressWord1 StationAddressWord2 R/W R/W R/W R/W BIT DESCRIPTION The least significant word of the station address, corresponding to address 0x54. The second least significant word of the station address, corresponding to address 0x56. The most significant word of the station address, corresponding to address 0x58.
The address comparison logic will compare the first 16 received destination address bits against StationAddressWord0, the second 16 received destination address bits against StationAddressWord1, and the third 16 received destination address bits against StationAddressWord2. The value set in StationAddress is not inserted into the source address field of frames transmitted by the IP100A LF. The source address field for every frame must be specified by the host system as part of the frame data contents. 11.4.21 TxDMABurstThresh Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x08 Default .......................... 0x08 Width ............................ 8 bits TxDMABurstThresh determines the threshold for when the IP100A LF makes transmit DMA bus master requests, based upon the available space in the transmit FIFO. TxDMABurstThresh represents free space in the transmit FIFO in multiples of 32 bytes. When the free space exceeds the threshold, the IP100A LF may make a transmit DMA request. However, if the free space exceeds the current FragLen subfield of the TxFrameControl field within the current TFD, the IP100A LF will make transmit DMA bus request regardless of whether the free space exceeds the TxDMABurstThresh or not. TxDMABurstThresh may be overridden by the TxDMAUrgentThresh mechanism. See the PCI Bus Master Operation section for information about the relationship between TxDMABurstThresh and TxDMAUrgentThresh. Any value less than 0x08 is invalid and is interpreted as 0x08. BIT 4..0 BIT NAME R/W TxDMABurstThresh R/W BIT DESCRIPTION Transmit DMA Burst Threshold. The number of 32-byte words which must be available in the transmit FIFO prior to assertion of a transmit DMA Burst Request. Reserved for future use.
7..5
Reserved
N/A
62/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.22 TxDMAListPtr Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x04 Default .......................... 0x00000000 Width ............................ 32 bits TxDMAListPtr holds the physical address of the current transmit DMA Frame Descriptor in the transmit DMA list. A value of zero in TxDMAListPtr is interpreted by the IP100A LF to mean that no more frames remain to be transferred by transmit DMA. TxDMAListPtr can only point to addresses on 8-byte boundaries, so TFD's must be aligned on 8-byte boundaries. TxDMAListPtr may be written directly by the host system to point the IP100A LF at the head of a newly created transmit DMA list. Writes to TxDMAListPtr are ignored while the current value in TxDMAListPtr is non-zero. To avoid access conflicts between the IP100A LF and the host system, the host system must set the TxDMAHalt bit of the DMACtrl register to a logic 1 before writing to TxDMAListPtr (unless the host system has specific knowledge that TxDMAListPtr contains zero). BIT 31..0 BIT NAME TxDMAListPtr R/W R/W BIT DESCRIPTION Transmit DMA List Pointer. TxDMAListPtr holds the physical address, on a 8-byte boundary, of the current TFD in the transmit DMA list. The host may examine the TxDMAListPtr to determine which frame(s) have been transferred by transmit DMA. Those frames in the transmit DMA list before the current TxDMAListPtr have already been transferred by transmit DMA. If the TxDMAListPtr is zero, then all the frames have been transmitted.
11.4.23 TxDMAPollPeriod Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x0a Default .......................... 0x00 Width ............................ 8 bits TxDMAPollPeriod determines the interval at which the current TFD is polled. If the current TFDs, TxDMANextPtr field is 0x00000000, the TxDMANextPtr field is polled to determine when a new TFD is ready to be processed. Polling is disabled when TxDMAPollPeriod is 0x00. TxDMAPollPeriod represents a multiple of 320 ns time intervals. The maximum value is 127 (or 40.64 us). BIT 6..0 7 BIT NAME TxDMAPollPeriod Reserved R/W R/W N/A BIT DESCRIPTION Transmit DMA Poll Period. The number of 320ns intervals between polls of the current TFD's TxDMANextPtr field. Reserved for future use.
63/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.24 TxDMAUrgentThresh Class............................. LAN I/O Registers, DMA Base Address ............... IoBaseAddress register value Address Offset .............. 0x09 Default .......................... 0x04 Width ............................ 8 bits When the number of used bytes in the transmit FIFO falls below the value in the TxDMAUrgentThresh, the transmit DMA logic will make an urgent bus master request. An urgent transmit DMA request will have priority over the receive DMA, unless it is also making an urgent request. A transmit DMA urgent request is not subject to the TxDMABurstThresh constraint. The relaxation of the TxDMABurstThresh constraint for this condition is because the transmit FIFO is close to under run, and burst efficiency is sacrificed to avoid FIFO under run. TxDMAUrgentThresh represents data in the transmit FIFO in multiples of 32 bytes. BIT 5..0 BIT NAME R/W BIT DESCRIPTION Transmit DMA Urgent Threshold. The minimum number of 32-byte words which must be occupied in the transmit FIFO to avoid assertion of a transmit DMA Urgent Request. Reserved for future use.
TxDMAUrgentThresh R/W
7..6
Reserved
N/A
11.4.25 TxReleaseThresh Class............................. LAN I/O Registers, FIFO Control Base Address ............... IoBaseAddress register value Address Offset .............. 0x5d Default .......................... 0x08 Width ............................ 8 bits TxReleaseThresh determines how much data of a frame must be transmitted before the transmit FIFO space can be released for use by another frame. Once the number of bytes equal to the value in TxReleaseThresh have been transmitted, that number of bytes are discarded from the transmit FIFO. Thereafter, bytes are discarded as they are transmitted to the network. A value of 0xff in TxReleaseThresh disables the release mechanism and transmit FIFO frame space is not released until the entire frame is transmitted. The TxReleaseError bit in the TxStatus register indicates when a frame experiences a collision after its release threshold has been crossed, preventing MAC from retry. When a release error occurs, the transmitter is disabled, and the frame's ID or sequence number is visible in TxStatus. BIT 7..0 BIT NAME TxReleaseThresh R/W R/W BIT DESCRIPTION Transmit Release Threshold. The number of 16 byte words which must be transmitted before the space in the transmit FIFO occupied by the transmitted data can be released. To avoid excessive release errors due to in-window collisions, TxReleaseThresh should be greater than or equal to 0x04.
64/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.4.26 TxStatus Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x46 Default .......................... 0x0000 Width ............................ 16 bits TxStatus returns the status of frame transmission or transmission attempts. TxStatus actually implements a queue of up to 31 transmit status bytes. A write of an arbitrary value to TxStatus will advance the queue to the next transmit status byte. BIT 0 1 BIT NAME Reserved TxReleaseError R/W N/A R BIT DESCRIPTION Reserved for future use. Transmit Release Error. If TxReleaseError is a logic 1, a transmit release error occurred, meaning that the frame transmission experienced a collision after the front of the frame had already been released to the transmit FIFO free space. See TxReleaseThresh register. Transmit Status Overflow. If TxReleaseError is a logic 1, the TxStatus stack is full and as a result the transmitter has been disabled. Writing an arbitrary value to TxStatus clears TxReleaseError but the transmitter must be re-enabled via the TxEnable bit of the MACCtrl1 register before transmissions may resume. Maximum Collisions. If MaxCollisions is a logic 1, a frame was not successfully transmitted due to encountering 16 collisions. The TxEnable bit of the MACCtrl1 register is used to recover from this condition. The frame is discarded from the transmit FIFO. Transmit Underrun. If TxUnderrun is a logic 1 the frame experienced an under run during the transmit process because the host system was unable to supply the frame data fast enough to keep up with the network data rate. An under run will halt the transmitter and the transmit FIFO. The TxReset bit of the AsicCtrl register is used to recover from an under run condition. Reserved for future use. Transmit Indicate Requested. If TxIndicateReqd is a logic 1, the TxIndicate bit of the TxFrameControl field for the corresponding TFD was set. Transmit Complete. If TxComplete is a logic 0, then the TxReleaseError, TxStatusOverflow, MaxCollisions, TxUnderrun, and TxIndicateReqd bits are undefined. If the host chooses to poll TxStatus while waiting for a frame transmission to complete, then TxComplete is used to determine that a frame transmission attempt has either experienced an error, or has completed successfully with the TxIndicate bit set in the TxFrameControl field of the corresponding TFD. Transmit Frame Identification. TxFrameId contains the value from the FrameId subfield within the TxFrameControl field of TFD corresponding to the currently transmitting or most recently transmitted frame. Host systems can use TxFrameId during transmit error recovery by scanning through the TFD's in the transmit DMA list, searching for a match between the TxFrameId value and a TxFrameControl's, FrameId value in the TFD.
65/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
2
TxStatusOverflow
R
3
MaxCollisions
R
4
TxUnderrun
R
5 6
Reserved TxIndicateReqd
N/A R
7
TxComplete
R
15..8
TxFrameId
R/W
IP100A LF
Preliminary Data Sheet
11.4.27 WakeEvent Class............................. LAN I/O Registers, Control and Status Base Address ............... IoBaseAddress register value Address Offset .............. 0x45 Default .......................... 0x00 Width ............................ 8 bits WakeEvent contains enable bits to control which types of events can generate a wake event to the host system. WakeEvent also contains status bits indicating the specific wake events which have occurred. BIT 0 BIT NAME WakePktEnable R/W R/W BIT DESCRIPTION Wake Packet Enable. If WakePktEnable is a logic 1, the IP100A LF may generate wake events via a PCI interrupt due to Wake Packet reception. The PmeEn bit in the PowerMgmtCtrl register must be set in order for WakePktEnable to be recognized. WakePktEnable has no effect in power mode D0. Magic Packet Enable. If MagicPktEnable is a logic 1, the IP100A LF may generate wake events via a PCI interrupt due to Magic Packet reception. The PmeEn bit in the PowerMgmtCtrl register must be set in order for MagicPktEnable to be recognized. MagicPktEnable has no effect in power mode D0. Link Event Enable. If LinkEventEnable is a logic 1, the IP100A LF may generate wake events via a PCI interrupt due to a change in link status (cable connect or disconnect). The PmeEn bit in the PowerMgmtCtrl register must be set in order for LinkEventEnable to be recognized. LinkEventEnable has no effect in power mode D0. Wake Polarity. If WakePolarity is a logic 1, the PMEN signal will be asserted HIGH. If WakePolarity is a logic 0, the PMEN signal will be asserted LOW. Wake Packet Event. If WakePktEvent is a logic 1, a wake packet (which meets the reception criteria set by the host system) has been received. WakePktEnable must be a logic 1 for WakePktEvent to operate. WakePktEvent is cleared following a read of the WakeEvent register. Magic Packet Event. If MagicPktEvent is a logic 1, a Magic Packet packet has been received. MagicPktEnable must be a logic 1 for MagicPktEvent to operate. MagicPktEvent is cleared following a read of the WakeEvent register. Link Event. If LinkEvent is a logic 1, a link status event has occurred. LinkEventEnable must be a logic 1 for LinkEvent to operate. LinkEvent is cleared following a read of the WakeEvent register. Wake On LAN Enable. If WakeOnLanEnable is a logic 1, the IP100A LF is in WakeOnLan mode regardless of the power management register settings in the configuration space. WakeOnLanEnable is loaded from the WakeOnLanEnable bit of AsicCtrl field within the EEPROM.
1
MagicPktEnable
R/W
2
LinkEventEnable
R/W
3
WakePolarity
R/W
4
WakePktEvent
R
5
MagicPktEvent
R
6
LinkEvent
R
7
WakeOnLanEnable R/W
66/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5 Statistic Registers The Statistic registers implement several counters defined in the IEEE 802.3 standard. Note reading a statistic register will also clear that register. The statistics gathering must be enabled by setting the StatisticsEnable bit in MACCtrl1 for the statistics registers to count events. 11.5.1 BroadcastFramesReceivedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x7d Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME BroadcastFramesReceivedOk R/W R/W BIT DESCRIPTION Broadcast Frames Received OK is the count of the number of frames that are successfully received with destination address equal to the broadcast address (0xFFFFFFFFFFFF). BroadcastFramesReceivedOk does not include frames received with frames too long, FCS, length or alignment errors, or frames lost due to internal MAC sublayer error (i.e.overrun). BroadcastFramesReceivedOk will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.22. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when BroadcastFramesReceivedOk reaches a value of 0xC0. BroadcastFramesReceivedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of BroadcastFramesReceivedOk also clears the register.
11.5.2 BroadcastFramesTransmittedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x7c Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME BroadcastFramesTransmittedOk R/W R/W BIT DESCRIPTION Broadcast Frames Transmitted is the count of the number of frames that are successfully transmitted to the broadcast address (0xFFFFFFFFFFFF). Frames transmitted to other multicast addresses are excluded from this statistic. BroadcastFramesTransmittedOk will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.19. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when BroadcastFramesTransmittedOk reaches a value of 0xC0. BroadcastFramesTransmittedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of BroadcastFramesTransmittedOk also clears the register.
67/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.3 CarrierSenseErrors Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x74 Default .......................... 0x00 Width ............................ 8 bits BIT 3..0 BIT NAME CarrierSenseErrors R/W R/W BIT DESCRIPTION Carrier Sense Errors counts the number of times that the carrier sense signal (CRS) was de-asserted (a logic 0) during the transmission of a frame without collision. The carrier sense signal is not monitored for the purpose of this statistic until after the preamble and start-of-frame delimiter fields of the Ethernet frame have been transmitted. CarrierSenseErrors will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.13. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when CarrierSenseErrors reaches a value of 0xC0. CarrierSenseErrors is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of CarrierSenseErrors also clears the register. Reserved for future use.
7..4
Reserved
R/W
11.5.4 FramesAbortedDueToXSColls Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x7b Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME FramesAbortedDueToXSColls R/W R/W BIT DESCRIPTION Frames Aborted Due to Excess Collisions counts the number of frames which are not transmitted successfully due to excessive collisions. FramesAbortedDueToXSColls will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.11. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when FramesAbortedDueToXSColls reaches a value of 0xC0. FramesAbortedDueToXSColls is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of FramesAbortedDueToXSColls also clears the register.
68/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.5 FramesLostRxErrors Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x79 Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME R/W BIT DESCRIPTION Frames Lost Due to Receive Errors is a count of the number of frames that should have been received (the destination address matched the filter criteria) but experienced a receive FIFO overrun error (the receive FIFO does not have enough free space to store the received data). FramesLostRxErrors only includes overruns that become apparent to the host system, and does not include frames that are completely ignored due to a completely full receive FIFO at the beginning of frame reception. FramesLostRxErrors will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.15. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when FramesLostRxErrors reaches a value of 0xC0. FramesLostRxErrors is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of FramesLostRxErrors also clears the register.
FramesLostRxErrors R/W
11.5.6 FramesReceivedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x72 Default .......................... 0x0000 Width ............................ 16 bits BIT 7..0 BIT NAME R/W BIT DESCRIPTION Frames Received OK is the count of the number of frames that are successfully received. FramesReceivedOk does not include frames received with frames too long, FCS, length or alignment errors, or frames lost due to internal MAC sublayer error (i.e. overrun). FramesReceivedOk will wrap around to zero after reaching 0xFFFF. See IEEE 802.3 Clause 30.3.1.1.5. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when FramesReceivedOk reaches a value of 0xC0. FramesReceivedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of FramesReceivedOk also clears the register.
FramesReceivedOk R/W
69/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.7 FramesTransmittedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset.............. 0x70 Default .......................... 0x0000 Width ............................ 16 bits BIT 7..0 BIT NAME R/W BIT DESCRIPTION Frames Transmitted OK is a count of the number of frames that are successfully transmitted. FramesTransmittedOk will wrap around to zero after reaching 0xFFFF. See IEEE 802.3 Clause 30.3.1.1.2. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when FramesTransmittedOk reaches a value of 0xC0. FramesTransmittedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of FramesTransmittedOk also clears the register.
FramesTransmitted- R/W OK
11.5.8 FramesWithDeferredXmission Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset.............. 0x78 Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME R/W BIT DESCRIPTION Frames with Deferred Transmit is a count of the number of frames that must delay their first attempt of transmission because the medium was busy. Frames involved in any collisions are not counted by FramesWithDeferredXmission. FramesWithDeferredXmission wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.9. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when FramesWithDeferredXmission reaches a value of 0xC0. FramesWithDeferredXmission is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of FramesWithDeferredXmission also clears the register.
FramesWithDeferred- R/W Xmission
70/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.9 FramesWithExcessiveDeferal Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x7a Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME R/W BIT DESCRIPTION Frames with Excessive Deferrals counts the number of frames that deferred for an excessive period of time (exceeding the defer limit). FramesWithExcessiveDeferal is only incremented once per LLC frame. FramesWithExcessiveDeferal will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.20. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when FramesWithExcessiveDeferal reaches a value of 0xC0. FramesWithExcessiveDeferal is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of FramesWithExcessiveDeferal also clears the register.
FramesWithExcessi R/W veDeferal
11.5.10 LateCollisions Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x75 Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME LateCollisions R/W R/W BIT DESCRIPTION Late Collisions is a count of the number of times that a collision has been detected later than 1 slot time into the transmitted frame. LateCollisions will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.10. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when LateCollisions reaches a value of 0xC0. LateCollisions is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of LateCollisions also clears the register.
71/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.11 MulticastFramesReceivedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x7f Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME MulticastFramesReceivedOk R/W R/W BIT DESCRIPTION Multicast Frames Received OK is the count of the number of frames that are successfully received to a group destination address other than the broadcast address (0xFFFFFFFFFFFF). MulticastFramesReceivedOk does not include frames received with frames too long, FCS, length or alignment errors, or frames lost due to internal MAC sublayer error (i.e. overrun). MulticastFramesReceivedOk will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.21. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when MulticastFramesReceivedOk reaches a value of 0xC0. MulticastFramesReceivedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of MulticastFramesReceivedOk also clears the register.
11.5.12 MulticastFramesTransmittedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x7e Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME MulticastFramesTransmittedOk R/W R/W BIT DESCRIPTION Multicast Frames Transmitted OK is a count of the number of frames that are successfully transmitted to a group destination address other than the broadcast address (0xFFFFFFFFFFFF). MulticastFramesTransmittedOk will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.18. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when MulticastFramesTransmittedOk reaches a value of 0xC0. MulticastFramesTransmittedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of MulticastFramesTransmittedOk also clears the register.
72/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.13 MultipleCollisionFrames Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x76 Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME MultipleCollisionFrames R/W R/W BIT DESCRIPTION Multiple Collision Frames is a count of the number of frames that are involved in more than one collision and are subsequently transmitted successfully. MultipleCollisionFrames will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.4. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when MultipleCollisionFrames reaches a value of 0xC0. MultipleCollisionFrames is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of MultipleCollisionFrames also clears the register.
11.5.14 OctetsReceivedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset .............. 0x68 Default .......................... 0x00000000 Width ............................ 32 bits (accessible as 2, 16 bit words) BIT 19..0 BIT NAME OctetsReceivedOk R/W R/W BIT DESCRIPTION Octets Received OK is the count of the number of data and padding octets in frames that are successfully received. OctetsReceivedOk does not include frames received with frames too long, FCS, length or alignment errors, or frames lost due to internal MAC sublayer error (i.e. overrun). OctetsReceivedOk will wrap around to zero after reaching 0xFFFFFFFF. See IEEE 802.3 Clause 30.3.1.1.14. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when OctetsReceivedOk reaches a value of 0xC0. OctetsReceivedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of OctetsReceivedOk also clears the register. Reserved for future use.
31..20
Reserved
N/A
73/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.5.15 OctetsTransmittedOk Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset.............. 0x6c Default .......................... 0x00000000 Width ............................ 32 bits (accessible as 2, 16 bit words) BIT 19..0 BIT NAME OctetsTransmittedOk R/W R/W BIT DESCRIPTION Octets Transmitted OK is a count of data and padding octets of frames successfully transmitte cm d. OctetsTransmittedOk will wrap around to zero after reaching 0xFFFFFFFF. See IEEE 802.3 Clause 30.3.1.1.8. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when OctetsTransmittedOk reaches a value of 0xC0. OctetsTransmittedOk is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of OctetsTransmittedOk also clears the register. Reserved for future use.
31..20
Reserved
N/A
11.5.16 SingleCollisionFrames Class............................. LAN I/O Registers, Statistics Base Address ............... IoBaseAddress register value Address Offset.............. 0x77 Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME Single Collision Frames R/W R/W BIT DESCRIPTION Single Collision Frames is a count of the number of frames that are involved in a single collision, and are subsequently transmitted successfully. SingleCollisionFrames will wrap around to zero after reaching 0xFF. See IEEE 802.3 Clause 30.3.1.1.3. An UpdateStats interrupt (UpdateStats bit within the IntStatus register) will occur when SingleCollisionFrames reaches a value of 0xC0. SingleCollisionFrames is enabled by writing a logic 1 to the StatisticsEnable bit in the MACCtrl1 register. A read of SingleCollisionFrames also clears the register.
74/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6 LAN PCI Configuration Registers PCI based systems use a slot-specific block of configuration registers to perform configuration of devices on the PCI bus. The configuration registers are accessed with PCI Configuration Cycles. Each PCI bus device is required to decode 256 bytes of configuration registers. Of these, the first 64 bytes are pre-defined by the PCI Specification. The remaining registers may be used as needed for PCI device-specific configuration registers. In PCI Configuration Cycles, the host system provides a slot-specific decode signal (IDSEL) which informs the PCI device that a configuration cycle is in progress. The PCI device responds by asserting DEVSELN, and decoding the specific configuration register from the address bus and the byte enable signals. See the PCI Expansion ROM specification for information on generating configuration cycles from driver software. Figure 14 shows the PCI configuration registers implemented by IP100A LF. All locations within the 256-byte configuration space that are not shown in the table, are not implemented and return zero when read. BYTE 3 Data PowerMgmtCap BYTE 2 BYTE 1 NextItemPtr BYTE 0 Capld ADDR OFFSET 0x54 0x50 0x4C 0x48 0x44 0x40 MaxLat MinGnt InterruptPin InterruptLine CapPtr ExpRomBaseAddress Subsystemld CISPointer SubsystemVendorld 0x3C 0x38 0x34 0x30 0x2C 0x28 0x24 0x20 0x1C 0x18 MemBaseAddress IoBaseAddress HeaderType ClassCode ConfigStatus Deviceld LatencyTimer CacheLineSize Revisionld ConfigCommand Vendorld 0x14 0x10 0x0C 0x08 0x04 0x00
PowerMgmtCtrl
FIGURE 14 : IP100A LF PCI Register Layout
75/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.1 CacheLineSize Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x0c Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME CacheLineSize R/W R/W BIT DESCRIPTION Cache Line Size. The system BIOS writes the system's cache line size into CacheLineSize. The host system uses CacheLineSize to optimize PCI bus master operation (choosing the best memory command, etc.). The value in CacheLineSize represents the number of double words in a cache. CacheLineSize values must be a power of two, from 0x04 to 0x80 (giving a range of 16 to 512 bytes). CacheLineSize values which are not a power of two, between 4 and 128 are interpreted as 0x00.
11.6.2 CapId Class............................. LAN PCI Configuration Registers, Power Management Base Address ............... PCI device configuration header start Address Offset .............. 0x50 Default .......................... 0x01 Width ............................ 8 bits BIT 7..0 BIT NAME CapId R/W R BIT DESCRIPTION Capabilities ID. CapId indicates the type of the capability data structure for the IP100A LF. CapId is set to the value 0x01 to indicate a PCI Power Management structure.
11.6.3 CapPtr Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x34 Default .......................... 0x50 Width ............................ 8 bits BIT 7..0 BIT NAME CapPtr R/W R BIT DESCRIPTION Capabilities Pointer. CapPtr indicates the beginning of a chain of registers which describe enhanced functions. CapPtr register returns 0x50, which is the address of the first in a series of power management registers.
76/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.4 CISPointer Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset.............. 0x28 Default Value ................ 0x00000802 Width ............................ 32 bits CISPointer identifies the location of the Card Information Structure (CIS). CISPointer contains the offset of CIS in memory space. CISPointer value is hardwired and can not be changed. Although the CIS is in memory, it is physically located in the EEPROM. Because the EEPROM access is so slow, the PCI target will issue a Retry for each new access. BIT 2..0 BIT NAME AddressSpaceIndicator R/W R BIT DESCRIPTION Address Space Indicator. AddressSpaceIndicator specifies the base address within the space indicated. The AddressSpaceOffset is added to AddressSpaceIndicator to identify the start of the CIS. The AddressSpaceIndicator value is 0x2, indicating the IP100A LF only supports CIS access in the memory pointed to by the PCI Base Address Register 1. Address Space Offset. AddressSpaceOffset is the offset from the base address specified by the PCI Base Address Register 1. The IP100A LF supports CIS in memory space. ROM Image Number. ROMImageNumber is 0x0 indicating the IP100A LF does not support CIS access in the expansion ROM.
27..3
AddressSpaceOffset R
31..28
ROMImageNumber R
11.6.5 ClassCode Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset.............. 0x09 Default .......................... 0x020000 Width ............................ 24 bits BIT 23..0 BIT NAME ClassCode R/W R BIT DESCRIPTION Class Code. ClassCode identifies the general function of the PCI device. A value of 0x020000 indicates an Ethernet network controller.
77/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.6 ConfigCommand Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x04 Default .......................... 0x0000 Width ............................ 16 bits ConfigCommand provides control over the adapter's ability to generate and respond to PCI cycles. When a zero is written to ConfigCommand, the IP100A LF is logically disconnected from the PCI bus, except for configuration cycles. BIT 0 1 BIT NAME IoSpace MemorySpace R/W R/W R/W BIT DESCRIPTION I/O Space. When IoSpace is a logic the IP100A LF can respond to I/O space accesses (if the IP100A LF is in the D0 power state). Memory Space. When MemorySpace, and the AddressDecodeEnable bit in the ExpRomBaseAddress register are both a logic 1, and if the IP100A LF is in the D0 power state, the IP100A LF is able to decode accesses to an Expansion ROM (if present). Bus Master. When BusMaster is a logic 1 the IP100A LF is able to initiate bus master cycles (if the adapter is in the D0 power state). Note: If the IP100A LF is initialized to PCI-X mode, BusMaster is ignored when initiating Split Completions. Reserved for future use. Memory Write and Invalidate Enable. When MWlEnable is a logic 1 the IP100A LF is permitted to use the MWI command. Reserved for future use. Parity Error Response. When ParityErrorResponse is a logic 1 the IP100A LF responds to parity errors as defined within the PCI specification. When ParityErrorResponse is a logic 0, the IP100A LF ignores parity errors. Reserved for future use. System Error Enable. When SERREnable is a logic 1, the SERRN signal is allowed to transition as appropriate. When SERREnable is a logic 0, the SERRN signal is a continuous logic 0. Reserved for future use.
2
BusMaster
R/W
3 4 5 6
Reserved MWlEnable Reserved
N/A R/W N/A
ParityErrorResponse R/W
7 8
Reserved SERREnable
N/A R/W
15..9
Reserved
N/A
78/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.7 ConfigStatus Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset.............. 0x06 Default .......................... 0x0210 Width ............................ 16 bits ConfigStatus is used to record status information for PCI bus events. Read/write bits inConfigStatus can only be reset, not set, by writing to this register. Bits are reset by writing a one to the corresponding bit. BIT 3..0 4 BIT NAME Reserved Capabilities R/W N/A R BIT DESCRIPTION Reserved for future use. Capabilities. Capabilities is a logic 1 to indicate a set of extended capabilities registers exists for the IP100A LF. The CapPtr register indicates the first address location of the extended capabilities register set. Reserved for future use. Fast Back to Back. When FastBackToBack is a logic 1 the IP100A LF when operating as a Target, supports fast back-to-back transactions as defined by the criteria in the section 3.4.2 of the PCI specification. Master Data Parity Error. When DataParityReported is a logic 1, the IP100A LF when operating as a Master, has detected the PERRN signal asserted, and the ParityErrorResponse bit in the ConfigCommand register as a logic 1. Device Select Timing. DevselTiming is used to encode the slowest time with which the IP100A LF asserts the DEVSELN signal. A value of 0x1 for DevselTiming indicates support for "medium" speed DEVSELN assertion. Signaled Target Abort. The IP100A LF sets SignaledTargetAbort to a logic 1 when the IP100A LF terminates a bus transaction with target-abort. Received Target Abort. The IP100A LF sets ReceivedTargetAbort to a logic 1 when, operating as a bus master, a IP100A LF bus transaction is terminated with target-abort. Received Master Abort. The IP100A LF sets ReceivedMasterAbort to a logic 1 when, operating as a bus master, a IP100A LF bus transaction is terminated with master-abort. Signaled System Error. When SignaledSystemError is a logic 1, the IP100A LF asserts the SERRN signal. Detected Parity Error. When DetectedParityError is a logic 1 the IP100A LF has detected a parity error, regardless of whether parity error handling is enabled.
6..5 7
Reserved FastBackToBack
N/A R
8
DataParityReported R/W
10..9
DevselTiming
R
11
SignaledTargetAbort R/W
12
ReceivedTargetAbort R/W
13
ReceivedMasterAbort R/W
14 15
SignaledSystemError R/W DetectedParityError R/W
79/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.8 Data Class............................. LAN PCI Configuration Registers, Power Management Base Address ............... PCI device configuration header start Address Offset .............. 0x57 Default Value ................ 0x00 Width ............................ 8 bits Data reports the power consumption of the IP100A LF. The values of DataSelect and DataScale in the PowerMgmtCtrl register are used to interpret the value of Data. BIT 7..0 BIT NAME Data R/W R BIT DESCRIPTION Data. Data reports power consumption and dissipation of the IP100A LF at worst-case conditions. To properly interpret the value read from Data, it must be scaled by the factor indicated in the DataScale field of the PowerMgmtCtrl register. The value of Data depends on the value of the DataSelect field of the PowerMgmtCtrl register. Data is loaded from the Data field in the EEPROM during a AutoInit reset. DATASELECT DATA 0x0 1 * DataScale Watts D0 Power Consumption 0x1 1 * DataScale Watts D1 Power Consumption 0x2 1 * DataScale Watts D2 Power Consumption 0x3 1 * DataScale Watts D3 Power Consumption 0x4 1 * DataScale Watts D4 Power Dissipated 0x5 1 * DataScale Watts D5 Power Dissipated 0x6 1 * DataScale Watts D6 Power Dissipated 0x7 1 * DataScale Watts D7 Power Dissipated 0x8 through 0xF 0x00 Reserved.
11.6.9 DeviceId Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x02 Default Value ................ 0x0200 Width ............................ 16 bits BIT 15..0 BIT NAME DeviceId R/W R BIT DESCRIPTION DeviceId contains the 16-bit device ID for the IP100A LF.
80/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.10 ExpRomBaseAddress Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x30 Default .......................... 0x00000000 Width ............................ 32 bits ExpRomBaseAddress allows the system to define the base address for the adapter's Expansion ROM. ExpRomBaseAddress is disabled (read only with a value of 0x00000000) when the IP100A LF is in Multi-Function Mode (see the Reserved/MultiFunction bit in the AsicCtrl register). BIT 0 BIT NAME AddressDecodeEnable R/W R/W BIT DESCRIPTION Address Decode Enable. If AddressDecodeEnable is a logic 0, the IP100A LF's Expansion ROM is disabled. If AddressDecodeEnable is a logic 1, and the MemorySpace bit in the ConfigCommand register is a logic 1, the IP100A LF will respond to accesses to the expansion ROM space. Reserved for future use. ROM Base Address. RomBaseAddress contains the expansion ROM base address, or the upper 16 bits (or 15 bits, depending on the state of the ExpRomSize bit in the AsicCtrl register) of the Expansion ROM address range. If the ExpRomSize bit in the AsicCtrl register is a logic 0, all 16 bits of RomBaseAddress are valid. If the ExpRomSize bit in the AsicCtrl register is a logic 1, bits 31 through 16 of RomBaseAddress are valid, with bit 15 ignored (set to a logic 0) during write operations.
14..1 31..15
Reserved RomBaseAddress
N/A R/W
11.6.11 HeaderType Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x0e Default .......................... 0x00 (single function)/0x80 (multi-function) Width ............................ 8 bits BIT 7..0 BIT NAME HeaderType R/W R BIT DESCRIPTION Header Type. If the Reserved/MultiFunction bit in the AsicCtrl register is a logic 0, HeaderType is set to 0x00 identifying the IP100A LF as a single-function PCI device and specifying the configuration register layout. If the Reserved/MultiFunction bit in the AsicCtrl register is a logic 1, HeaderType is set to 0x80 identifying the IP100A LF as a multi-function PCI device and specifying the configuration register layout.
81/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.12 InterruptLine Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x3c Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME InterruptLine R/W R/W BIT DESCRIPTION Interrupt Line. InterruptLine specifies the interrupt level used by the IP100A LF. By setting InterruptLine the host system may configure the appropriate interrupt vector for its Interrupt Service Routine. For 80x86 processor based host systems, InterruptLine corresponds to the IRQ number (0x00 through 0x0F), with the value 0xFF corresponding to disabled interrupts.
11.6.13 InterruptPin Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x3d Default .......................... 0x01 Width ............................ 8 bits BIT 7..0 BIT NAME InterruptPin R/W R BIT DESCRIPTION Interrupt Pin. InterruptPin indicates which PCI interrupt signal the IP100A LF will utilize. The IP100A LF always utilizes the INTAN interrupt signal, corresponding to an InterruptPin value of 0x01.
11.6.14 IoBaseAddress Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x10 Default .......................... 0x00000001 Width ............................ 32 bits IoBaseAddress is used to define the I/O base address for the IP100A LF. PCI systems requires that the I/O base address be set as if the system used 32-bit I/O addressing. The upper 25 bits of IoBaseAddress are read/write accessible, indicating that the IP100A LF requires 128 bytes of I/O space in the system I/O map. BIT 0 BIT NAME IoBaseAddrInd R/W R BIT DESCRIPTION I/O Base Address Indicator. When IoBaseAddrInd is a logic 1, IoBaseAddress contains the valid I/O base address for the IP100A LF. Reserved for future use. I/O Base Address. IoBaseAddress contains the 25 bit I/O base address value. The IP100A LF uses 128 bytes of I/O address space.
6..1 31..7
Reserved IoBaseAddress
N/A R/W
82/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.15 LatencyTimer Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x0d Default .......................... 0x00 Width ............................ 8 bits BIT 2..0 7..3 BIT NAME Reserved LatencyTimer R/W N/A R/W BIT DESCRIPTION Reserved for future use. Latency Timer. LatencyTimer indicates, in increments of 8 bus clocks, the length of time which the IP100A LF may hold the PCI bus in the presence of other bus requestors. Whenever the IP100A LF asserts the FRAMEN signal, the latency timer is started. When the latency timer count expires, the IP100A LF must relinquish the bus as soon as its GNTN signal has been deasserted.
11.6.16 MaxLat Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x3f Default .......................... 0x0A Width ............................ 8 bits BIT 7..0 BIT NAME MaxLat R/W R BIT DESCRIPTION Maximum Latency. MaxLat specifies, in 250 ns increments, how often the IP100A LF requires bus access while operating as a bus master. Bits 5 through 1 of the MaxLat value are loaded from the ConfigParm field within an EEPROM during auto initialization of the IP100A LF.
11.6.17 MemBaseAddress Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x14 Default .......................... 0x00000000 Width ............................ 32 bits MemBaseAddress can be disabled via loading of the ConfigParm field from an EEPROM during auto-ini-tialization of the IP100A LF. BIT 0 BIT NAME MemBaseAddrInd R/W R BIT DESCRIPTION Memory Base Address Indicator. When MemBaseAddrInd is a logic 1, MemBaseAddrInd contains the valid memory base address.
83/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 2..1 BIT NAME MemMapType R/W R BIT DESCRIPTION Memory Map Type. MemMapType defines how the host system maps the IP100A LF's registers within the host system memory space. Bit 2 of MemMapType is always a logic 0, while bit 1 is loaded from the Lower1Meg bit of the ConfigParm field within an EEPROM during auto initialization of the IP100A LF. BIT 2 BIT 1 REGISTER MAPPING 0 0 Anywhere within a 32 bit address space 0 1 Lower 1 megabyte of 32 bit address space 1 x Undefined Reserved for future use. Memory Base Address. MemBaseAddress contains the 25 bit memory base address value. The IP100A LF uses 128 bytes of I/O space.
6..3 31..7
Reserved MemBaseAddress
N/A R/W
11.6.18 MinGnt Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x3e Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME MinGnt R/W R BIT DESCRIPTION Minimum Grant Time. MinGnt specifies, in 250 ns increments, how long a burst period the IP100A LF requires when operating as a bus master. Bits 7 through 4 of the MinGnt value are loaded from the ConfigParm field within an EEPROM during auto initialization of the IP100A LF.
11.6.19 NextItemPtr Class............................. LAN PCI Configuration Registers, Power Management Base Address ............... PCI device configuration header start Address Offset .............. 0x51 Default .......................... 0x00 Width ............................ 8 bits BIT 7..0 BIT NAME NextItemPtr R/W R BIT DESCRIPTION Next Item Pointer. NextItemPtr indicates the next capability data structure in the capabilities list. When NextItemPtr is set to the value 0x00, there are no further data structures.
84/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.20 PowerMgmtCap Class............................. LAN PCI Configuration Registers, Power Management Base Address ............... PCI device configuration header start Address Offset .............. 0x52 Default Value ................ 0x7602 Width ............................ 16 bits PowerMgmtCap provides information about the IP100A LF's power management capabilities. Several bits are loaded from the EEPROM during auto-initialization. BIT 2..0 3 4 BIT NAME Versi on Reserved Vaux R/W R N/A R BIT DESCRIPTION Version. Version is set to 0x2, indicating PCI Bus Power Management Specification Revision 1.1. Reserved for future use. Auxiliary Voltage. If Vaux is a logic 1, auxiliary power via the PCI Bus is required from the system to support PME in the D3cold state. If Vaux is a logic 0, auxiliary power is supplied from elsewhere (i.e. not from the PCI Bus) to support PME in the D3cold state. Reserved for future use. D1 Power State Support. When D1Support is a logic 1, the IP100A LF supports the D1 power state. D1Support is loaded from the ConfigParm field of an EEPROM during auto initialization of the IP100A LF. D2 Power State Support. When D2Support is a logic 1, the IP100A LF supports the D2 power state. D2Support is loaded from the ConfigParm field of an EEPROM during auto initialization of the IP100A LF. Power Management Event Support. PmeSupport indicates the power states from which the IP100A LF is able to generate a power management event by asserting the PMEN signal. Each bit corresponds to a power state. A logic 1 in a particular bit position indicates that events can be generated from the indicated power state. POWER MANAGEMENT EVENT BIT BIT BIT BIT BIT MAY BE GENERATED FROM 15 14 13 12 11 STATE x x x x 1 D0 x x x 1 x D1 x x 1 x x D2 x 1 x x x D3Hot 1 x x x x D3Cold PmeSupport bit 11 and 14 are hard-wired to 0 and 1 respectively, while bits 12, 13, and 15 are loaded from the ConfigParm field of an EEPROM during auto initialization of the IP100A LF.
8..5 9
Reserved D1Support
N/A R
10
D2Support
R
15..11
PmeSupport
R
85/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.6.21 PowerMgmtCtrl Class............................. LAN PCI Configuration Registers, Power Management Base Address ............... PCI device configuration header start Address Offset .............. 0x54 Default Value ................ 0x4000 Width ............................ 16 bits PowerMgmtCtrl allows control over the power state and the power management interrupts. BIT 1..0 BIT NAME PowerState R/W R/W BIT DESCRIPTION Power State. PowerState indicates the current power state of the IP100A LF. If PowerState is set to a value other than 0x0, the IP100A LF will not respond to PCI I/O or memory cycles, nor will the IP100A LF be able to generate PCI bus master cycles. BIT 1 BIT 0 POWER STATE 0 0 D0 0 1 D1 1 0 D2 1 1 D3 Reserved for future use. Power Management Event Enable. When PmeEn is a logic 1, the IP100A LF is allowed to report wake events on the PMEN signal. The criteria for generating wake events is defined by the WakeEvent register. PmeEn is loaded from the ConfigParm field of an EEPROM during auto initialization of the IP100A LF. Data Select. DataSelect is used to select which data is to be reported through the Data register and DataScale field. Data Scale. DataScale indicates the scaling factor to be used when interpreting the value of the Data register. The interpretation of the scale values is defined as follows: DATASCALE SCALE FACTOR 0x0 Unknown 0x1 0.1 0x2 0.01 0x3 0.001 Power Management Event Status. When PmeStatus is a logic 1 a wake event has occurred. PmeStatus may be a logic 1 regardless of the value of PmeEn. Writing a logic 1 to PmeStatus will set PmeStatus to a logic 0. Writing a logic 0 to PmeStatus has no effect.
7..2 8
Reserved PmeEn
N/A R/W
12..9 14..13
DataSelect DataScale
R/W R
15
PmeStatus
R/W
11.6.22 RevisionId Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x08 Default .......................... Depends on revision of actual device. See description below. Width ............................ 8 bits
86/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
BIT 7..0 BIT NAME RevisionId R/W R BIT DESCRIPTION Revision ID. RevisionId contains the revision code for the IP100A LF. REVISIONID SILICON REVISION 30 B0
11.6.23 SubsystemId Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x2e Default .......................... 0x0000 Width ............................ 16 bits BIT 15..0 BIT NAME SubsystemId R/W R BIT DESCRIPTION Subsystem ID. SubsystemId contains the value loaded from the ConfigParm field within an EEPROM during auto initialization of the IP100A LF.
11.6.24 SubsystemVendorId Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x2c Default .......................... EEPROM Value Width ............................ 16 bits BIT 15..0 BIT NAME R/W SubsystemVendorId R BIT DESCRIPTION Subsystem Vendor ID. SubsystemVendorId contains the value loaded from the ConfigParm field within an EEPROM during auto initialization of the IP100A LF.
11.6.25 VendorId Class............................. LAN PCI Configuration Registers, Configuration Base Address ............... PCI device configuration header start Address Offset .............. 0x00 Default .......................... 0x13f0 Width ............................ 16 bits BIT 15..0 BIT NAME VendorId R/W R BIT DESCRIPTION Vendor ID. VendorId contains the unique 16-bit manufacturer's ID as allocated by the PCI Special Interest Group. The manufacturer ID is 0x13F0.
87/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.7 EEPROM Data Format Figure 15 summarizes the layout of the EEPROM. 16 BIT WORD StationAddress StationAddress StationAddress ADDR OFFSET 0x12 0x11 0x10 0x0F 0x0E 0x0D 0x0C 0x0B FunctionsCtrl : : Subsystemld SubsystemVendorld AsicCtrl ConfigParm 0x0A : : 0x03 0x02 0x01 0x00
FIGURE 15 : IP100A LF EEPROM Field Layout 11.7.1 AsicCtrl Class............................. EEPROM Data Format Base Address ............... 0x00, address written to EepromCtrl register Address Offset .............. 0x01 Access Mode ................ Read Only Width ............................ 16 bits AsicCtrl supplies the value for the least significant byte of the AsicCtrl register and the WakeEvent register. BIT 0 BIT NAME LEDFlashSpeed BIT DESCRIPTION This bit determines the flashing speed of the LED. Set to 0 will have LED On and Off ratio of 5 : 35 ms(Fast) Set to 1 will have LED On and Off ratio of 20 : 60 ms(Slow) LEDFlashSpeed corresponds to the LEDFlashSpeed bit in the AsicCtrl register. 0: Set LED Mode 0 1: Set LED Mode 1 LED Mode corresponds to the LED Mode bit in the AsicCtrl register. Transmit Large Frames Enable. TxLargeEnable corresponds to the TxLargeEnable bit in the AsicCtrl register. Receive Large Frames Enable. RxLargeEnable corresponds to the RxLargeEnable bit in the AsicCtrl register.
88/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
1
LED Mode
2 3
TxLargeEnable RxLargeEnable
IP100A LF
Preliminary Data Sheet
BIT 4 5 6 7 14..8 15 BIT NAME ExpRomDisable PhySpeed10 PhySpeed100 PhyMedia Reserved BIT DESCRIPTION Expansion ROM Disable. ExpRomDisable ExpRomDisable bit in the AsicCtrl register. corresponds to the
Physical Layer Device Speed 10Mbps. PhySpeed10 corresponds to the PhySpeed10 bit in the AsicCtrl register. Physical Layer Device Speed 100Mbps. PhySpeed100 corresponds to the PhySpeed100 bit in the AsicCtrl register. Physical Layer Device Media. PhyMedia corresponds to the PhyMedia bit in the AsicCtrl register. Reserved for future use.
WakeOnLanEnable Wake On LAN Enable. WakeOnLanEnable corresponds to the WakeOnLanEnable bit in the WakeEvent register.
11.7.2 ConfigParm Class............................. EEPROM Data Format Base Address ............... 0x00, address written to EepromCtrl register Address Offset .............. 0x00 Access Mode ................ Read Only Width ............................ 16 bits BIT 0 1 2 BIT NAME FastBackToBack Lower1Meg DisableMemBase BIT DESCRIPTION Fast Back to Back. FastBackToBack corresponds FastBackToBack bit in the ConfigStatus register.
to
the
Lower 1 Megabyte. Lower1Meg corresponds to bit 1 of the MemMapType bit in the MemBaseAddress register. Disable Memory Base Address Register. DisableMemBase does not correspond directly to any register accessible by the host system. If DisableMemBase is a logic 1 during auto initialization of the IP100A LF, the MemBaseAddress register will be disabled. When disabled, the value returned when the MemBaseAddress register is read is undefined. D3 Cold Power Management Event. D3ColdPme corresponds to the PmeSupport bit in the PowerMgmtCap register. D1 Power State Support. D1Support corresponds to the D1Support bit in the PowerMgmtCap register. D2 Power State Support. D2Support corresponds to the D2Support bit in the PowerMgmtCap register. Power Management Event Enable. PmeEn corresponds to the PmeEn bit in the PowerMgmtCtrl register. Minimum Grant. MinGnt corresponds to bits 7 through 4 of the MinGnt register. Maximum Latency. MaxLat corresponds to bits 5 through 1 of the MaxLat register.
3 4 5 6 10..7 15..11
D3ColdPme D1Support D2Support PmeEn MinGnt MaxLat
89/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.7.3 FunctionsCtrl Class............................. EEPROM Data Format Base Address ............... 0x00, address written to EepromCtrl register Address Offset .............. 0x0A Access Mode ................ Read Only Width ............................ 16 bits BIT 0 BIT NAME LDPS Enable BIT DESCRIPTION Link-Down-Power-Saving mode. Set this bit to 1 will reduce the power usage of IP100A LF if the link between IP100A LF and another terminal has terminated. Enable Auto Cross Function. At logic 1, IP100A LF will be able to use both crossover UTP wire and non-crossover UTP wire. Reserved for future use. Default setting as 0 Enable Last Gasp Function. At logic 1, IP100A LF will activate last gasp function, and IP100A LF will be able to send last gasp frames. These 3 bits will decide the number of Last Gasp Packets to send. Since there are 3 bits controlling the amount of packet sent, thus the maximum number of packets is 8 frames.
1 2 3 6..4
Auto-Cross-Over Enable Reserved Last-Gasp Control Last-Gasp Repeat Time
7
15..8
Last-Gasp OP Code Decision of the Last Gasp OP Code. This bit determines the OP Code within the Last Gasp frames. At 0: Last-Gasp packet send OP Code is 0001 At 1: Last-Gasp packet send OP Code is 0100 DSP Settings Setting to PHY DSP
11.7.4 StationAddress Class............................. EEPROM Data Format Base Address ............... 0x00, address written to EepromCtrl register Address Offset .............. 0x10, 0x11, 0x12 Access Mode ................ Read Only Width ............................ 48 bits BIT 15..0 31..16 47..32 BIT NAME StationAddress0 StationAddress1 StationAddress2 BIT DESCRIPTION Station Address 0. StationAddress0 (offset 0x10) corresponds to the StationAddressWord0 field of the StationAddress register. Station Address 1. StationAddress1 (offset 0x11) corresponds to the StationAddressWord1 field of the StationAddress register. Station Address 2. StationAddress2 (offset 0x12) corresponds to the StationAddressWord2 field of the StationAddress register.
90/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
11.7.5 SubsystemId Class............................. EEPROM Data Format Base Address ............... 0x00, address written to EepromCtrl register Address Offset .............. 0x03 Access Mode ................ Read Only Width ............................ 16 bits BIT 15..0 BIT NAME SubsystemId BIT DESCRIPTION Subsystem ID. SubsystemId corresponds to the SubsystemId register.
11.7.6 SubsystemVendorId Class............................. EEPROM Data Format Base Address ............... 0x00, address written to EepromCtrl register Address Offset .............. 0x02 Access Mode ................ Read Only Width ............................ 16 bits BIT 15..0 BIT NAME BIT DESCRIPTION corresponds to the
SubsystemVendorId Subsystem Vendor ID. SubsystemVendorId SubsystemVendorId register.
91/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
12 Signal Requirements
Note, all signal requirements are guaranteed by design only.
12.1
Absolute Maximum Ratings
Storage Temperature...................-65C to +150C Ambient Temperature ....................-65C to +70C Supply Voltage................................-0.3V to +3.6V Environmental stresses above those listed in Absolute Maximum Ratings may cause permanent damage resulting in device failure. Functionality at or above the limits listed below is not guaranteed. Exposure to the environmental stress at the levels listed below for extended periods may adversely affect device reliability.
12.2
Operating Ranges
Commercial Devices Temperature (TA ) .............................. 0C to +70C Supply Voltages (VCC 3.3V) ................ +3.3V 5% Supply Voltages (VCC 2.5V) ................ +2.5V 5% Input voltages .......................... +3.3V or +5V 5% Operating ranges define the limits of guaranteed device functionality.
92/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
DC Characteristics DC characteristics are defined over commercial operating ranges unless specified otherwise. PARAMETER PARAMETER SYMBOL DESCRIPTION Vcc 3.3V 3.3V power voltage Icc 3.3V Vcc 2.5V Icc 2.5V TTL I/O VIH VIL IIN VOH VOL IOTS 3.3V power current 2.5V power voltage 2.5V power current Input high voltage Input low voltage Input leakage current Output high voltage Output low voltage Output tri-state leakage Iol = 4 mA 2.7 6 5 MHz square wave input 300 365 430 VIN = VCC /GND -10 2.4 0.4 10 2.37 TEST CONDITIONS MIN 3.13 TYP MAX 3.47 10.6 2.63 159.5 2 0.8 10 UNIT V mA V mA V V A V V A V k mV
100BASE-TX RECEIVE VB RXP/RXN Input Bias Voltage RIN SON RXP/RXN Differential Input Resistance Signal Detect Turn-On Threshold
100BASE-TX TRANSMIT (MEASURED DIFFERENTIALLY AFTER 1:1 TRANSFORMER) VPDO Peak Differential Output 50from each 0.95 1.05 output to VCC VOI Output Voltage Imbalance 50from each 0.4 output to VCC Overshoot VREF Reference Voltage of ISET 1.25 1.4 10 5 MHz square wave 250 10BASE-T RECEIVE VB10 RXP/RXM Input Bias Voltage RIN10 VSQ RXP/RXN Differential Input Resistance Squelch Threshold 5
V V % V V k mV
10BASE-T TRANSMIT (MEASURED DIFFERENTIALLY AFTER THE 1:1 TRANSFORMER) VP Peak Differential Output 50from each 2.2 2.8 output to VCC TABLE 3 : DC Characteristics
V
93/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
12.3 AC Characteristics PARAMETER DESCRIPTION TEST CONDITIONS MIN 300 1 30 11 11 2 2 2 28 7 10 12 0 40 1us 250 250 250 100 50 0 70 3 0 0.7 25 3.5 500 500 5 500 0.5 1.4 11 12 TYP MAX UNIT ns s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ps ns ns ns ns PARAMETER SYMBOL
PCI INTERFACE Trc RSTN cycle Trr Tcc Tch Tcl Trv Trvp Trzo Troz Tsu Tsup1 Tsup2 Thd Trstoff Rising edge or RSTN to chip recovery PCICLK cycle PCICLK high PCICLK low PCICLK rise to bused signal valid PCICLK rise to REQN, GNTN valid PCICLK rise to signal on PCICLK rise to signal off bused signal setup wrt PCICLK rise GNTN setup wrt PCICLK rise REQN setup wrt PCICLK rise signal hold wrt PCICLK rise RSTN low to output signal float
EEPROM INTERFACE Tskc EESK cycle Tskh Tskl Tcs Tpd Tcsk Tcsh Tdos Tdoh EESK high EESK low EECS low EEDI valid wrt EESK rise EECS setup wrt EESK rise EECS hold wrt EESK fall EEDO setup wrt EESK rise EEDO hold wrt EESK rise
100BASE-TX MDI TR /TF Rise/Fall Time TIMB TDCD TJ Rise/Fall Time Imbalance Duty Cycle Distortion Maximum output jitter (peak to peak)
10BASE-T MDI TR10 /TF10 Rise/Fall Time TJ10 Transmit Jitter
94/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
PARAMETER SYMBOL PARAMETER DESCRIPTION TEST CONDITIONS MIN 40 16 16 TABLE 4 : Switching Characteristics
trc RSTN tcl PCICLK trv BUSSED SIGNALS tsu tcc tch
TYP
MAX 40 24 24
UNIT ns ns ns
MISC INTERFACE Tcc CLK25 cycle Tch Tcl CLK25 high CLK25 low
IP100A LF
trvp REQN trvp GNTN trzo ANY SIGNAL ANY SIGNAL
tsup2
tsup1
thd
troz
trstoff
FIGURE 16 : PCI Switching Characteristics
tcs EECS tcskv tskl tskc tskh tcsh
IP100A LF
EESK tpd EEDI
A7
A0 tdos tdoh D15 D0
EEDO
FIGURE 17 : EEPROM Switching Characteristics
95/97 Copyright (c) 2004, IC Plus Corp. March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
12.4 Thermal Data Theta Ja 38.2 Theta Jc 16 Conditions 2 Layer PCB Units o C/W
13 Order Information
Part No. IP100A IP100A LF Package 128-PIN QFP 128-PIN QFP Notice Lead free
96/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17
IP100A LF
Preliminary Data Sheet
14 Physical Dimensions
128 PQFP Outline Dimensions
HD D
128 103
Unit: Inches/mm
1
102
38
65
39
64
e
b GAGE PLANE A2
c
HE
E
Symbol A1 A2 b c HD D HE E e L L1 y
Dimensions In Inches Min. Nom. Max. 0.010 0.014 0.018 0.107 0.112 0.117 0.007 0.009 0.011 0.004 0.006 0.008 0.669 0.677 0.685 0.547 0.551 0.555 0.906 0.913 0.921 0.783 0.787 0.791 0.020 0.025 0.035 0.041 0.063 0.004 0 12
Dimensions In mm Min. Nom. Max. 0.25 0.35 0.45 2.73 2.85 2.97 0.17 0.22 0.27 0.09 0.15 0.20 17.00 17.20 17.40 13.90 14.00 14.10 23.00 23.20 23.40 19.90 20.00 20.10 0.50 0.65 0.88 1.03 1.60 0.10 0 12
D
L1
y
A1
L
Note: 1. Dimension D & E do not include mold protrusion. 2. Dimension B does not include dambar protrusion. Total in excess of the B dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot.
IC Plus Corp.
Headquarters 10F, No.47, Lane 2, Kwang-Fu Road, Sec. 2, Hsin-Chu City, Taiwan 300, R.O.C. TEL: 886-3-575-0275 FAX: 886-3-575-0475 Website: www.icplus.com.tw Sales Office 4F, No. 106, Hsin-Tai-Wu Road, Sec.1, Hsi-Chih, Taipei Hsien, Taiwan 221, R.O.C. TEL: 886-2-2696-1669 FAX: 886-2-2696-2220
97/97 Copyright (c) 2004, IC Plus Corp.
March. 30, 2007 IP100A LF-DS-R17

▲Up To Search▲

Price & Availability of IP100ALF

	To Download IP100ALF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .